Made of injection-molded ultra-high-strength polypropylene copolymer resin, this SKB Cases I-Series 2011-10 Wheeled Utility Case is made to withstand the most extreme and demanding shipping, handling, and working conditions on the planet. The case is offered here with a ThinkTank-designed padded photo divider insert that is custom-made to fit the case's roomy 19.5 x 10.5 x 8" interior and features long and short removable and adjustable dividers that you can position to perfectly fit your gear. For complete protection the case also has a convoluted eggcrate foam lid insert and an 8.5" thick foam base layer.

Case design features include gasket sealing to an IP67-rating that makes it dust and waterproof, a molded-in hinge for added protection, dual stainless steel reinforced padlock holes, and a trigger release latch system. Polypropylene resin is not only strong, it is also resistant to a variety of hazards that you may encounter such as impacts, ultraviolet (UV) radiation, solvents, corrosion, and even fungi. A pressure relief valve comes into play especially during air transport by regulating the internal pressure, keeping your gear and the case from getting crushed and allowing you to open the case without having to break a tough pressurized seal that may develop. Built-in skate-style casters allow you to wheel the case behind you by using either the snap-down grip handle or the telescoping pull handle.

IP67-Rated Dust and Waterproof    Built for Extreme & Demanding Conditions    Polypropylene Copolymer Resin Material    UV/Solvent/Corrosion/Fungus Resistant    ThinkTank-Designed Photo Divider Insert    Padded Protection for Delicate Gear    Extending Handle with Low-Profile Wheels    Pressure Relief Valve    Molded-In Hinge and Padlock Holes

Related Questions and Answers

Q: 1. Will this fit 2 Pentax 67 cameras without wood grip?

A: Hi Vladimir, I'm not personally familiar with the size of the Pentax 67 camera. One spot I found online stated it was 6.97 x3.97 x3.58 . If that is correct then it will have no problem fitting into the case. The internal dimensions of the case including the padded dividers are 19.5 x10.5 x6 I think you should easily be able to fit a couple of cameras and other accessories as well. There is also a version of this case with a lid organizer instead of foam if that interests you. The model number for that is 3i-2011-7DL. Thank you,Will

Q: 2. Is this a TSA-approved overhead bin size (like the Pelican 1510 and 1535)? I already have issues with my over-stuffed Think Tank Airport Security bag.

A: The maximum dimensions for a carry-on bag are 9 inches x 14 inches x 22 inches (22 cm x 35 cm x 56 cm), including handles and wheels.

Q: 3. Is this case deep enough to hold a NIKON D610 with battery drive without the lid having to be closed with pressure?. In other words, easily?

A: Harvey, I have an SKB 2217-10, and don't have a D610.The bottom section on mine is 9 deep, without compressing the bottom of the Thinktank inserts. The top lid accounts for about 3/4' of the advertised depth, the Thinktank bottom about 1/4' uncompressed.This lends me to believe that the 2011-7 likely has a depth of 6 to 6 1/4 before the top foam would begin to touch the camera. You can measure the D610 plus battery pack + bottom bracket if you have one. I can however speak to the quality of the SKB/Thinktank Combo. It's excellent. Rugged, sufficient lock clasps (for TSA or other locks). Check the B&H, SKB and Thinktank sites for all the models. (Each site doesn't have all the model sizes.)I put the Thinktank lid case in mine instead of the foam, very handy for laptops.Good luck.

Q: 4. Will a MacBook Pro 16 fit in the sleeve?

A: The dimensions of a Macbook Pro 16" are 14.09 x 9.68 x 0.64", so it will fit into the 15" laptop sleeve of this case.

Q: 5. If i use this in my case will i also be able to add a lid divider?

A: Hi Colter, You will not be able to add a lid organizer to this particular case. The insert takes up the full volume of the case. I would suggest the 3i-2011-7BP if you would like a removable insert. This case has a removable backpack that has space for a laptop to fit into. Another option is our 3i-2011-7DL. Thank you,Will

Q: 6. Does the size of this case fit airline carry on sizes?

A: Yes it does. While you will always want to check with the airline you are traveling with, carry-on luggage is usually 22 x 14 x 9 inches. This case is designed for carry-on with exterior dimensions of 21.9 x 14.0 x 9.0".

Q: 7. What are the interior and exterior dimensions of this case?

A: Exterior: 21.9 x 14.0 x 9.0 / 55.6 x 35.6 x 22.9 cmInterior: 20.4 x 11.4 x 7.5 / 51.8 x 29.0 x 19.1 cm

Q: 8. Does anyone know if this case will fit in an overhead luggage compartment, or is it too large as a carry on?

A: According to spec from most airlines, yes it is approved size for a carry on.

Q: 9. Is there a Trekpak system that can be used with this?

A: There are only TrekPak divider systems for Pelican cases at this time.

Q: 10. Does this case fir the size for airline carry on?

A: Yes, it is within the size restrictions for carry on.