Equipped with white and stealthy infrared LEDs, the SureFire Infrared Scout Light Pro Weaponlight can be mounted on a Picatinny or M-LOK rail and swivels as needed—toward the rifle to reduce snagging on brush or away from it to make room for other gear. The tan Infrared Scout Light Pro delivers 350 lumens of white light through a Total Internal Reflection lens, for a bright beam with long throw and ample surrounding light. Twist the bezel to switch from white to 120mW, 860nm IR light. Power is controlled on a momentary or constant-on basis with a push-button tail cap switch, shrouded to guard against accidental activation. The light's hard-anodized aluminum housing is O-ring sealed against the elements. Power is supplied by one CR123A battery with one hour of runtime.

350 Lumens White Light, 120mW IR    Mounts on Picatinny or M-LOK Rails    Swivels for Optimal Positioning    Tail Cap On/Off, Bevel Twist for Mode    Momentary and Constant-On Modes    Total Internal Reflection Lens    Runs on One CR123A Battery    Type III Hard-Anodized Aluminum Body    O-Ring Sealed    Tempered Glass Lens

• 350-lumen output white LED
• 120mW inrared light, 860nm
• Total Internal Reflection (TIR) lens for bright beam with ample surrounding light

• On/off: push button
• Location: tail cap
• Momentary and constant-on modes
• Shrouded tail cap helps prevent accidental activation
• Twist bezel to toggle between white and IR light

• Mounts on Picatinny top rails or forend M-LOK rails
• Pivots as needed: away from weapon to accommodate other gear or closer to weapon for smoother profile with less likelihood of snagging on brush
• Includes Picatinny and M-LOK cleats

• Lightweight aluminum housing
• Scratch- and corrosion-resistant Type III hard-anodized finish
• O-ring sealed for weather resistance
• Impact-resistant tempered window

Related Questions and Answers

Q: 1. Instructions?

A: Yes, click the link below to view; https://onlinemanual.nikonimglib.com/d7500/en/20_remote_control_01.html

Q: 2. how do you use the ML-L3 in the bulb setting?

A: While usage of the remote may differ slightly depending on your camera model (which was not listed - you may want to refer to your camera's instruction manual for more assistance), according to Nikon USA's website (link included below), they state that when the ML-L3 remote control is used in M mode, users can selected '- -' as the shutter speed. At this setting, the shutter opens when the shutter-release button on the ML-L3 remote control is pressed (2 seconds after the button is pressed in delayed remote mode) and remains open until the remote-control shutter-release button is pressed a second time (maximum exposure time is 30 minutes).As stated, using the - - setting is recommended instead of the BULB setting for long exposure needs if you are using the ML-L3 remote to wirelessly trigger the camera's shutter.https://a href= http://support.nikonusa.com/app/answers/detail/a_id/11940//using-the-ml-l3-remote-control target= _blank support.nikonusa.com/app/answers/detail/a_id/11940//using-the-ml-l3-remote-control/a

Q: 3. compatible with nikon D500?

A: This remote will not work. However, this one will. Nikon WR-T10 Wireless Remote Controller Transmitter B&H # NIWRT10

Q: 4. will this work with a nikon d3100? Its not listed in the overview, but its a newer camera so is it possible the description is just out of date and it will work with the 3100?

A: No this will not work because the d3100 does not have an IR receiver. The MC-DC2 wired remote will work.

Q: 5. Is this compatible with Nikon Coolpix 510?

A: No. The Coolpix 510 does not have an infrared sensor.

Q: 6. Can I use this with my Nikon D3000 in bulb mode to shoot longer than 30 sec? If yes, please share how. Thanks.

A: You would rotate the rear control dial to until you reach the bulb mode and press the shutter button on the ML-L3. It will keep the shutter open in bulb mode for 30 minutes or until the shutter button on it is pressed again.

Q: 7. Can this ML-L3 be configured to work with the SMD RFN4s receiver?.I lost the SMD RFN4s transmitter.

A: The ML-L3 is an optical remote shutter release which only works with select Nikon cameras.

Q: 8. Does this remote work with Nikon D700?

A: Sorry but the ML-L3 does not work on the D700. The D700 does not have an infrared sensor. You must use one of the Nikon wired remotes.

Q: 9. Is this remote compatible with a Nikon D5600 ?

A: This remote is not compatible with a D5600.

Q: 10. Compatible with coolpix p7700? -thank you!

A: Yes, the ML-L3 is compatible with the P7700.