These gray SHELL Mittens in size 8 from The Heat Company keep your vulnerable hands and fingers warm and protected from the elements. 

Made from windproof and highly water-resistant material, the mittens have goatskin leather palms that are not only tough and wear resistant, but provide a secure and slip-resistant grip. Each mitten is lined with warm and comfortable Primaloft Gold insulation. When you need to use your fingers to operate a camera, access your phone, check your stats on a sport watch, or perform any one of a thousand tasks, simply fold back the finger and thumb flaps to expose your digits. A magnetic clasp keeps the flap out of your way, so it won't interfere with what you're doing. For added protection without sacrificing dexterity, layer the mittens over a pair of optional liners.

An adjustable cinch at the wrist has straps that allow you to remove the mitten from your hand without having to put it down where it can get filled with snow or lost. Slip a disposable hand warmer into the small, zippered pocket on the back of the hand, or use it to stow small accessories like credit cards or your ID.

The size 8 mitten fits 7-7.8" hands, measured around the palm of your dominant hand just below the knuckles. The Heat Company recommends sizing up if you are in between sizes.

Durable Nylon Shell    Windproof and Water Resistant    Tough Goatskin Leather Palm    Warm Primaloft Gold Insulation    Finger & Thumb Flaps with Magnet Clasp    Pocket for Handwarmer or Essentials    Elastic Wrist Straps

Related Questions and Answers

Q: 1. Does this fit a phantom 4? It doesn't look the same as the new Koozam phantom 4 backpack

A: This case is compatible with the Phantom 1, Phantom 2, Phantom 2 Vision, Phantom 2 Vision+, and Phantom 3 models. The Phantom 4 and accessories will not fit.

Q: 2. What is CCT? I see it on the back of the unit. What does it do? What is its intention?

A: The label CCT on the back of the Godox LED6Bi Litemons light allows you to adjust the color temperature of the light. You can adjust the color temperature in the range from 3200 to 6500K (in 9 steps)

Q: 3. The product photos all show a bubble level, but the specs say bubble levels none. If I order this, will it have a bubble level or not?

A: The full size lever release clamp will feature a bubble-level while the compact lever release clamp does not.

Q: 4. Is the Arca plate included with the purchase of this ball head?

A: No the Quick Release Plates is Not Included

Q: 5. Does this fit on a bogen tripod?

A: No, It's for a manfrotto tripod

Q: 6. Mainly taking it for backpacking. Does it support d850 and 14-24/70-200 lens along with RRS 1 series tripod.

A: Yes, it will work fine with your gear. Good little ball head with good load capacity.

Q: 7. Does the lever in the lever release clamp have a safety switch so that I won't accidentally flip it open...??

A: I have read the other responses and agree with them all. Now for an engineering answer. The lever uses a design called an offset cam. The first 10-15 degrees of rotation require a lot of force. After that it becomes continually easier as the cam rotates increasing the lever arm length and the mechanical advantage. This feedback works in reverse when you close the head with the last few degrees of rotation being very hard. You know that the camera is locked without looking.

Q: 8. Does this ball head allow to put the camera in a vertical position and tilt the camera up and down?

A: Yes, you can maneuver the head in any position.

Q: 9. I just bought 1 and received it today, I absolutely love it. My question is that I find the lever clamp stiff and hard to close after I install a plate, I put such much force that I have to hold the entire unit firmly or tighten the pan dial till it stops turning, is that normal?

A: Yes, you are correct, basically all arca compatible plates vary in width by mm's, just enough to cause an issue. RRS plates or brackets are best to be used in RRS heads or ones that specifically say compatible with RRS.

Q: 10. Does it reclock the SDI output?

A: The SDI loop output does not reclock when using the AVMATRIX Mini SC1112 3G-SDI to HDMI Pocket-Size Broadcast Converter.