The black, 14 RU over 16 RU Odyssey Innovative Designs Pro Combo Rack Case with Casters is made of ABS plastic laminate over 3/8" plywood and designed to protect and transport an audio mixer, controller, amplifiers, and rack gear. The angled top helps to provide easy access to controls, while the 16 rack spaces below house and protect your precious amplifiers and signal processors.

The case has steel hardware and chrome-plated butterfly latches. It is transported by recessed, spring-loaded handles and a caster board with four 3.5" heavy-duty casters, two of which are locking. The heavy-duty steel ball corners and aluminum edging ensure the case will last a lifetime.

For Mixers and Controllers    ABS Laminate over 3/8" Plywood    14-Space Slanted Rack    16-Space Vertical Rack    ATA Rated    Removable Top and Front Lids    Chrome-Plated Butterfly Latches    Recessed, Spring-Loaded Handles    Caster Board with Four Wheels    Steel Corners and Aluminum Edging

• Black case built of ABS plastic laminate over 3/8" plywood, made to ship, carry, and protect audio mixers and controllers
• Meets ATA 300 specifications for shipping cases
• Removable top and front lids
• Recessed, chrome-plated butterfly latches with padlock loop
• Recessed, spring-loaded, chrome-plated handles 
• Caster board with four wheels (two with brakes)
• Steel corners and aluminum edging
• Rubber feet to prevent skidding
• 3/8" ply construction
• Lid interior height is 9"
• Front cover depth is 3"
• Top Slanted Rack: 14 spaces
• Bottom Vertical Rack: 16 spaces
• Heavy-duty ball corners
• Recessed latches and spring-loaded handles
• Four 3.5" heavy-duty casters, 2 with brakes (caster assembly is required)
• Top of slanted rail at its rear is 4.75" high from the top of the front vertical rail
• Rail to back of the rack is 26"
• Rear trap door is 15.5" x 24.5"
• Limited lifetime warranty

Related Questions and Answers

Q: 1. Will this handle work with the Tilta Advanced Ring Grip for DJI RS 3 Pro and RS 2 Gimbals BH #TITGAARG?

A: The DJI Focus Pro Grip of the DJI Focus Pro All-In-One Combo can mount onto the NATO mounting points of the Tilta Advanced Ring Grip for DJI RS 3 Pro and RS 2 Gimbals, but the grip is designed to be connected directly to the focus motor and may not be a functional setup.

Q: 2. Can you have LiDAR focus overlays on the high bright monitor without the bracket to connect the the fiz hand unit to monitor?

A: No, DJI Focus Pro Hand Unit from the DJI Focus Pro All-In-One Combo or the DJI Wireless Video Transmitter (BH #DJVDC) would have to be connected to the DJI High-Bright Remote Monitor in order for the Lidar to communicate with the monitor.

Q: 3. Can you change the lidar from 30 frames a second

A: At this moment we are not aware that the DJI Lidar sensor capture rate can be changed.

Q: 4. Where is the link for the new DJI Focus Pro LiDAR to DJI Transmission Cable Hub? That’s need to hook up the transmission system?

A: There are a few products that were sent to influencers that have yet to be released by DJI. Both the new cable hub and the DJI Hi Bright Monitor mount have not been released as products from DJI. We do not have a timeframe when they will be available.

Q: 5. I see it says it will work with RS 3 & RS 4 Pro gimbals, but will it still work with the RS 2?

A: No, the DJI Focus Pro All-In-One Combo is not compatible with the DJI RS2 Pro Gimbal Stabilizer.

Q: 6. How can one engage auto-focus from the hand unit? The reviewer says its not possible?

A: No, autofocus cannot be engaged from the hand unit of the DJI Focus Pro All-In-One Combo at this time.

Q: 7. Does the Focus Pro Grip also let you control a zoom and/or iris motor along with the focus? Or only 1 motor at a time?

A: The Focus Pro Grip with the DJI Focus Pro All-In-One Combo can switch the control dial from Focus to Zoom via the touchscreen. The motor must be set to the intended mode for the respective control.

Q: 8. Can we use the Focus pro with non hard hard-stop lens ?

A: No, DJI recommends only using lenses with hard stops like Cinema Lenses when using the DJI Focus Pro All-In-One Combo.

Q: 9. Can the motor and hand unit be used without the grip and lidar?

A: Yes, the DJI Focus Pro All-In-One Combo can be used without the Grip,and Lidar. The motor could be powered by the Gimbal and the Handwheel connects to the motor wirelessly.

Q: 10. Is there longer cables that work with the motors and lidar? USB-c has much longer options but they do not seem to work

A: At this moment we do not have longer cable options for the DJI Focus Pro All-In-One Combo.