Ensure your sound remains clean with the PowerStation AC Power Bar from iFi Audio. Designed to protect connected equipment from distracting radio frequency and electromagnetic interference, the iFi PowerStation utilizes built-in polarity and ground detection to keep signals clean and lower noise floors by more than 40 dB. Individually contained connections also prevent cross-contamination between devices plugged into the eight NEMA 5-15R outlets, while 13 AWG 99.9999% oxygen-free, high-conductivity copper ensures ample conductivity. A 4mm banana socket accommodates a grounding cable for audio systems and the PowerStation's Intelligent Ground smart diagnostic tool prevents the formation of a ground loop, further ensuring signals remain clean. Built-in surge protection also safeguards your gear from voltage spikes or power surges, effective to 30,000A at 1000V for 10 microseconds.

8 x NEMA 5-15R Outlets    30,000A @ 1000V/10 μs Surge Protection    Protects AV Equipment from RFI & EMI    Reduces Noise Floor by >40 dB    13 AWG 99.9999% OFHC Copper    Intelligent Ground Prevents Ground Loop    Polarity & Earth Detection    Compatible with the iFi AC iPurifier

The PowerStation uses PurCopper, a form of 99.9999 percent pure OFHC (oxygen-free high-conductivity) continuous-cast copper, throughout its build for conductivity. This includes 13 AWG, heavy-gauge internal wiring with multi-layered polymer insulation, solid PurCopper busbars, and the conductive elements of the outlets themselves.

The iFi Wireless Purification System (WPS) is a complex circuit that reduces power line noise without audible or measured side effects.

The LED indicators show polarity and earth detection. As usual, green is good, red signifies an issue. There are four possible combinations that can be found in a brief table in the user manual.

The Over-Voltage Surge Protection (OSP) is an auto detection and cut-off circuit. Should it detect an excessive power surge or short in the mains electricity, it will automatically cut off. If the issue persists, it will not reboot to protect your equipment from harm. It is effective to a maximum 30,000A at 1000V/10 uS.

Intelligent Ground only actively provides an earth or ground connection if your system needs one. It will not create a ground loop, even if the system is already earthed or grounded.

You can use AC iPurifiers in the PowerStation. The more AC iPurifiers you use, the cleaner the overall power. If the AC iPurifier is placed in the middle of the PowerStation it will also act as a noise shield. Noise is reduced, isolated, and confined to the respective left and right sections of the AC iPurifier. Use it to separate your analogue and digital devices.

Based on military tech, iFi Active Noise Cancellation II neutralizes incoming noise. It does this in a similar way to active noise-cancelling headphones, generating a signal identical to that of the incoming electrical noise but in the opposite phase, actively cancelling it out. This is highly effective at removing low- and mid-frequency noise, while passive insulating filters deal with higher-frequency interference. This combination is measurably more effective at eradicating noise corrupting a USB signal than devices relying solely on passive filtering.

It reduces the noise floor by >40 dB (>100x).

Related Questions and Answers

Q: 1. Will this work with my Zoom 3030 and my Zoom GFX-707 effects pedals?

A: Yes, the Planet Waves PW-CT-9V Regulated AC-DC 9V Power Adapter is compatible for use with the Zoom Player 3030 Multi-effects Processor and the Zoom GFX-707 Guitar Effects Processor Pedals. The PW-CT-9V has the same power rating as the Zoom AD-16 9V Power Supply Adapter For Zoom Effects Pedals (B&H # ZOAD16D) which is designed specifically for use with Zoom effects pedals, including the 3030 and GFX-707. Both power supplies are rated at 9V, 500mA.

Q: 2. Can this CA-110 charger power the Vixia camera HF R700 without the battery installed?

A: Yes - this will power the camera directly from an AC wall socket.

Q: 3. Which one is compatible with Sony camcorders, like the PXW-Z280?

A: We are not aware of this being compatible with a Sony PXW-Z280.

Q: 4. will this work with Vixia HF R800?

A: Yes, this adapter is compatible with the Canon Vixia HF R800.

Q: 5. Will this work with Benro tripod arms?

A: No. The following unit is designed and made for the MVR901EPLA, MVR901EPEX tripod units.

Q: 6. is it work with canon HF R706 ?

A: Yes, this will charge the Canon LEGRIA HF R706. This is for USA electrical systems so you will need a plug adapter for other countries. Here is a list of all plug adapters we currently sell. http://bhpho.to/2f1UTyA

Q: 7. WILL this adapter work on a VIXIA HF R800?

A: Yes, this adapter is compatible with the Canon Vixia HF R800.

Q: 8. Will this work with a Canon VIXIA HF G30 Camcorder?

A: It will not, this is for smaller Vixia options. For the G30 you will need B&H # CACA570 instead. This power supply works with your camera. https://bhpho.to/2jkeNoi

Q: 9. From time to time I'd like to have a pan arm mounted on my Manfrotto 393 heavy lens gimbal. Could I use this accessory clamp to adapt a Manfrotto 500HLV pan bar or their MVAPANBARM handle? Would the tightening knob's bolt length, metric threading and toothed adjustment pitch be compatible? I'd like to stay with an all-Manfrotto set-up.

A: This will work with any pan bar between .75 to .98" in diameter.

Q: 10. What is the output voltage and amperage of this charger/psu?

A: The Canon CA-110 Compact AC Power Adapter & Charger provides 5.3 V DC, 1.5 A.