Offered as a 6-pack, the orange Sprig Cable Management Device presents filmmakers and sound recordists with a fast, convenient, and simple solution for keeping cable runs tidy on their cinema equipment and camera rigs. With a quick twist, it can be installed in or removed from a 1/4"-20 threaded hole in a hurry. Since it is constructed from a durable injection-molded material, it can withstand the rigors of life on location.

Anchors into 1/4"-20 Threaded Hole    Durable Injection-Molded Material    Convenient Cable Hook    Twist to Install or Remove

Sprig makes it more convenient to organize cables along the surfaces of your cinema equipment. Its patent-pending design features a flexible thread for a lightning-quick install that keeps you on pace with even the most blistering schedules.

Since Sprig models the functionality of a 1/4"-20 screw, a twist of the wrist is all it takes to achieve a snug fit or loosen to remove. In a hurry? Go ahead and release with a firm tug. The tough and flexible Sprig can handle it.

Sprig is injection molded from a strong and flexible material to create a cable hook that survives on set and won't crack under pressure.

Related Questions and Answers

Q: 1. latency?

A: Z Cam IPMAN S has a 50-meter line of sight range. No info on latency was given. We tried a in house test and noticed the following unit has a 100-150ms latency. I wish the range were farther, but 50 meters (164 feet) with a clear signal will work great as we conducted the test in our superstore.

Q: 2. Does this work with the C500 MK II?

A: Yes it does. This cable is even included in the box with the C500 Mark II.

Q: 3. Can this be used to START / STOP recording on an Atomos Ninja V? If so, what cable is needed?

A: According to Atomos, " The Ninja V uses LANC Slave and so a LANC controller must first be attached to a camera and the output taken out via a Y cable to the Ninja V". A similar setup would be required when using the SmallRig Threaded Side Handle with Record Start/Stop Remote Trigger to trigger a Ninja V monitor.

Q: 4. How many of these can you run side by side? Meaning, how many separate channels is feasible?

A: The Z CAM IPMAN S HDMI Wireless Video Streaming Device could be used with 3 or more pairs TX and RX. I have confirmed that up to 3 pairs of IPMAN S (Tx + Rx) would work with no problem. .However, Zcam says it is unlimited.

Q: 5. Looking for something similar for Canon (R6) but with no luck , is it just something canon can’t do?

A: A similar grip to the SmallRig Threaded Side Handle with Record Start/Stop Remote Trigger that is compatible with the Canon R6 would be the Kondor Blue Trigger Wing Side Handle (Raven Black), BH #KOKBWSHBK.

Q: 6. How long does it work on a 2900mAh battery pack?

A: The Z CAM IPMAN S HDMI Wireless Video Streaming Device does not list power drain. We suspect a 2900mAh is on the shorter amount of time. To get through your job, have several spares.

Q: 7. is the start stop compatible with the Lumix s5ii. I know its not on the list but is that because the list is out of date?

A: Yes, the Panasonic cable included with the SmallRig Threaded Side Handle with Record Start/Stop Remote Trigger should support the Lumix S5II even though it has not been tested by Smallrig.. Tested cameras list. https://bhpho.to/4aVgiSF

Q: 8. Receiver and transmitter?

A: The Z CAM IPMAN can be used as transmitter or receiver by switching Rx and Tx mode.

Q: 9. What size tripod leg will this fit? I have a tripod leg which has a 42mm diameter.

A: The Really Right Stuff Series 4 Threaded Tripod Leg Collar has a diameter of 40.7mm.

Q: 10. Can I use this unit to wirelessly transmit video from my a7iii to my PC? The a7iii would send video wirelessly to this unit, and then this unit would be connected via USB-C to my PC.

A: You will need to connect your camera to the Z CAM IPMAN S with an HDMI cable and then connect the transmitter to your PC with a USB-C cable. This device requires an HDMI connection with a camera with an HDMI output.