Place your Atlona Velocity 10" touch panel on a table top, lectern, or other flat surface with this Tabletop Mount to create a freestanding AV control panel. The mount's VESA 75 x 75mm standard holes are compatible with the VESA pattern on the back of the touch panel, allowing the panel to be secured with the included screws. Once attached, the mount allows the panel's height and operating angle to be adjusted to best suit the user.

For Atlona Velocity 10" Touch Panels    VESA 75 x 75mm Mounting    Adjust Height and Operating Angle    Includes Mounting Screws

• Atlona Velocity All-in-One 10" Touch Panel with Gateway
• Atlona Velocity 10" Touch Panel

Related Questions and Answers

Q: 1. I would like to use this with a Ronin. Has anyone attempted this? Please share your experience. I'm looking into a A7SII, ES-T17 cage, Nucleus M and Ronin combo.

A: The Tilta is new so reports are just coming in. From the specs, this should work on any Ronin. You could be the one who reports right here on the pages of B&H.

Q: 2. Will this also control Panasonic projectors?

A: The Epson ELPSP10 PixiePlus Control System - BH #EPELPSP10 is not designed for compatibility with Panasonic or any other brand of projector.

Q: 3. Does this include the IR cable that runs to the projector and gets taped to the IR window on the projector?

A: The Projector Controller for Epson ships with: 1 PixiePlus Circuit Board 6 White Plastic Button Inserts and 7 Rubberized Button Pads IR Emitter IR Emitter Bud Holder 1 6VDC Regulated Power Supply 50 RS-232 Dongle Cable Assembly IR Emitter Cable Anchors 2 Bezels (ivory and white) Installation Guide PixiePlus ELPSP10 Supplement Mounting Screws Paper Clip (for IR-learning)Required and Optional parts and accessories (not included): 1 Leviton Decora wall plate (Required. Match to bezelcolor.) 1 Single-Gang Back Box (Optional. SP Controls recommendsusing a grounded back box) PixiePlus programming tool (PXE-PGM-TOOL) for reconfigurationof the PixiePlus RS-232 codes or schedule events(Optional)

Q: 4. does it work wit fuji Xh2s and a siriu 24 mm anarmorphic lens?

A: The Tilta Nucleus M works independently from practically any camera/lens type. All it requires is the right power supply and rigging options.

Q: 5. Is the power cable compatible with a Sony alpha A7siii?

A: no it is not. you will need to power the unit with a separate power source

Q: 6. What is a Gear Mod?

A: The 0.8 MOD Drive Gears is the connection that the Follow Focus Motors make to the lens. You can see them in the top right hand corner in this photo.https://bit.ly/2LcWpev0.8 Gears are found on Cinema Lenses Standard. If you have a photography lens you will be using you may just need to add a gear ring to them to make the connection. Here is a link to a Gear Ring that will work with this system.https://bhpho.to/2KROmYs

Q: 7. If I can use 18650 batteries to power the system, will it be strong enough to work and focus on a sigma 18-35 or 50-100?

A: Powering off of the internal 18650 batteries provides less torque than powering through a P-tap connector. However, there should be enough power pull focus for photo lenses.

Q: 8. Does the start/stop trigger work on the Fuji Xt3?

A: Yes, there is the Tilta Nucleus-M Run/Stop Cable for FUJIFILM X-T3 (27") https://www.bhphotovideo.com/c/product/1547291-REG/tilta_rs_01_fj_nucleus_m_runstop_cable_for.html

Q: 9. how can i power the motor from other than dtap?

A: you Can power the motors from from the fiz and handle units although this defeats the purpose when using the fiz. You could also purchase a V-mount adapter so you can use a V-mount with a ptap.

Q: 10. I purchased the nitecore NL1835 3500mAh 18650 12.6wh and I can not get them to fit into any of the battery ports. Do I have the wrong size?

A: You may have the wrong batteries. We currently recommend the EVO Gimbals IMR 18650 - 3 Battery Pack for Rage3, B&H # EVO50645, for this product. They are the proper size. https://bhpho.to/2MEzf2g