Quickly mount and remove your video monitor from a C-stand or another 5/8" Baby pin support using the VESA to 5/8" Baby Pin Adapter from E-Image. This durable aluminum adapter supports monitors between 13 and 30" weighing up to 33 lb and has a 150° tilt function for optimal positioning.

Supports up to 33 lb, 13-30" Monitor    75 x 75 & 100 x 100mm VESA Support    Mounts onto 5/8" Baby Pin or C-Stand    150° Tilt Adjustment    Durable Aluminum Construction

• Monitors with a 75 x 75 or 100 x 100mm VESA pattern
• C-stand or support with male 5/8" Baby pin

• Video monitors measuring from 13 to 30"
• Maximum payload of 33 lb

Tilts up to 150° for optimal viewing

Related Questions and Answers

Q: 1. What does the hole configuration look like on the bottom? Is it 1/4-20, 3/8-16 or a combination of both?

A: It's a combination of 1/4 and 3/8 screw threadings. There's a line of threadings down the center bottom that has multiple of each. Hope this helps!

Q: 2. What size thread is the knob to secure this to a 5/8 stud? If you were to purchase a replacement knob, what size would you buy?

A: Unfortunately, Impact does not publish the thread size of the locking knob of this header. The knob can be obtained through Impact directly as a replacement part by calling 1-212-594-2120.

Q: 3. Can this be used with the Ursa-mini with the shoulder mount kit and not have it interfere with the shoulder cushion?

A: You mount this plate to the tripod (with a plate that fits your particular head) and the camera slides on and locks. Then you flip the side lever, slide the camera off, and place it on your shoulder. It is not used at the same time as the shoulder mount. I use it with the Zacuto VCT Universal baseplate. Have also used it on URSA, but haven't tried it on the mini.

Q: 4. Does this work with the Panasonic AJ-PX380?

A: Hello,It does indeed! In fact, it will work with any VCT-14 V-Wedge equipment out there!

Q: 5. Can this be used with the C300 Mark II?

A: It really has nothing to do with the camera so much as it has to do with what tripod you have and what baseplate you have for your camera rig. The VCT quick release plate will work with about any tripod head, but you'd have to get a VCT mount to attach to your base plate. That being said, if that's all stuff that fits into your rig - it works great.

Q: 6. If this extension is used to connect a tether table to a runway stand base, will the setup be sturdy enough to use a laptop safely or will the whole thing be too wobbly?

A: It will be too wobbly

Q: 7. I am looking for something like this but with a baby plate to mount to the ceiling instead of mounting two parts with a separate baby plate. Do you sell any telescopic extensions with baby plate?

A: If looking to bolt the plate into the ceiling, you may only do so by using a separate baby plate like the Matthews Baby Plate - 3 B&H # MABP3 with this extension.

Q: 8. Is this compatible with the inovativ cart c stand clamp holder?

A: No, the Matthews Telescopic Baby Stand Extension is too small for the Inovativ C-Stand Storage Clamps.

Q: 9. Can this be used with a Blackmagic URSA Camera?

A: The E-Image Quick-Release Tripod Adapter is compatible with the Blackmagic URSA.

Q: 10. Will this lock down the Zacuto VCT universal baseplate?

A: Yes, it works fine with the Zacuto VTC. I had to adjust the Zacuto plate slightly, but once that was done it locked in very solid.