Elvid's 7" RigVision is a very lightweight on-camera monitor offering high image quality and incorporating remote shutter release functionality. Set up and monitor your shots in 1280 x 800 high resolution and sharp 800:1 contrast ratio. Analyze focus, exposure, and other characteristics with False Color, Zebra, Pixel-to-Pixel, Histogram, and altogether over a dozen features. Connect to simultaneously active HDMI and Composite inputs, and loop out the HDMI signal to a recorder or other device. Connect a shutter release cable to a port on the side and take photos using a shutter button on the front panel. For audio monitoring, the RigVision features a built-in speaker, headphone output, and on-screen audio level meter. An assortment of supplied accessories includes two interchangeable DV battery plates, V-mount and Gold-mount plate adapter, and shutter release cables.

13 functions in total are assignable across three function buttons on the front panel. The included DV battery plates are for Sony F-970 and Canon LP-E6 compatible batteries, and they simply snap into place without any screws required, and additional plates are optionally available from Elvid. An AC power adapter is also included. Weighing less than 1 lb, the 7" RigVision rests easily on your camera while providing a large monitoring display.

Backlit IPS Monitor with Shutter Release    1280 x 800 Resolution    800:1 Contrast Ratio    HDMI & Composite Inputs    HDMI Loop Output    False Color, Zebra, Histogram & More    DSLR Scaling for Full Screen Viewing    Includes F-970 & LP-E6 Battery Plates    Canon Shutter Release Cable Supplied    Nikon Shutter Release Cable Supplied

• Lightweight LED backlit IPS on-camera monitor
• Remote shutter release port and shutter button
• 1280 x 800 resolution
• 800:1 contrast ratio
• 178° viewing angle
• HDMI and Composite inputs; HDMI loop output
• Fully compatible with RED cameras
• Built-in speaker and headphone output
• Includes interchangeable F-970 and LP-E6 DV battery plates
• Includes V-mount and Gold-mount plate adapter
• DC power cable included
• Canon 3-pin and Nikon 10-pin shutter release cables supplied

• Histogram
• 1:1 Pixel-to-Pixel
• Picture-in-Picture (for when the HDMI and Composite inputs are used simultaneously)
• H/V Delay
• Underscan
• Center Marker
• Zoom (up to 8x)
• False Color
• Peaking
• Zebra
• Color Bar
• Image Flip
• Audio Level Meter
• Adjustable color temperature

Related Questions and Answers

Q: 1. Will this work with a Nikon D3s and a Nikon Coolpix P-1000? Also what is the second box attached in the configuration picture?

A: Yes, the following monitor will accommodate both units.

Q: 2. Does this monitor have different aspect ratio guides such as 1:85 and 2:35?

A: This monitor can display the following: 16:10, 16:9, 4:3, 1.85:1, and 2.35:1.

Q: 3. Will this monitor stretch the DSLR signal to fill the screen?

A: I do not use it with a DSLR, but I think I read in the manual that it will stretch it.

Q: 4. Will this monitor connect to a 5DIII? If so, what type of cable will it require? Same question for a 7DII. Thank you.

A: Hey Mike, to answer your question. Yes, this will connect to an 5D Mark III. The cable you need is already included. My only advice for you is to buy an additional battery as the monitor does not come with one. You can buy the same battery that the 5D uses and that's a huge plus. Hope this helps. The monitor is great, I've had it for about 2 months and no problems. Just a 5 sec lag when you start up the monitor and camera. So when you have them connected, just let it do it's thing and the image will show up after at least 5 sec.

Q: 5. Does this unit work with the Canon 40D ?

A: Yes, using composite video instead of HDMI, this should work with a Canon 40D. You will, however, need an RCA coupler (B&H # TEARCAFRCAF) to connect the composite video cable that came with your 40D to the composite video cable that comes with this monitor (both cables are 1/8 male to RCA male).

Q: 6. Can I use this monitor as HDR monitor with Blackmagic decklink card in my computer for color grade HDR ?

A: While the Elvid 5" RigVision HDR On-Camera Touchscreen Monitor could be connected to a Blackmagic Design DeckLink card, the monitor is designed for on camera use. For an HDR monitor for color grading an option would be the BenQ SW321C 32" 16:9 4K HDR IPS Photo and Video Editing Monitor, BH #BESW321C.

Q: 7. Will it work with Canon EOS cameras ?

A: Yes, the Elvid 5" RigVision HDR On-Camera Touchscreen Monitor would work with Most any camera that can output video on HDMI. Please note that most Canon Camera models will require a Mini to HDMI cable to connect to the display. ZILR Hyper-Thin High-Speed Mini-HDMI to HDMI Cable with Ethernet (17.7") BH #ZI4KP60MC17 Also make sure to add a Battery: Watson NP-F770 Battery Kit with Compact AC/DC Charger BH #WANPF770CK

Q: 8. What type of V mount battery would this monitor accept with the plate adapter?

A: The included plate adapter is not a battery mount. The plate adapter is used to mount a v or gold mount battery plate on to the monitor itself. So the choice is yours.

Q: 9. Will this work on the Panasonic GH4?

A: It works with HDMI input so as long as the camera has that function it will work fine

Q: 10. Can I see what the false color settings are anywhere ? Can you set them yourself?

A: The false color settings are displayed on the screen when false color is enabled. The majority of the parameters for the False color settings can not be adjusted however, you are able adjust the over and under exposure warnings.