Organize and safely store your batteries with the Storacell Carbon Fiber Magnetic AA Battery Holder. Made of a strong and lightweight material, the holder is ideal for professionals and outdoor enthusiasts who burn batteries in the field and need to keep spares for camera flash units, flashlights, GPS units, radios, or any small electronic device that is hungry for power. A small magnet is embedded at the bottom each individual cell and secures your batteries in place while you move or climb. When its time to swap batteries, simply push up on the bottom of the battery and it will easily slide out for friction-free removal. This version is designed to hold 12 AA batteries.

Holds 12 AA Batteries    Strong & Lightweight Carbon Fiber    Magnets Secure Batteries in Place    Easy Battery Removal

Related Questions and Answers

Q: 1. How long does it take to fully charge these batteries when using the Panasonic charger? Thanks.

A: Good question, sir. I charge before batteries are fully discharged: 2 hours which typical which suggests a rather fast charge. Batteries are fairly warm afterwards. To get the very most charge, I've found a day after charging, re-install & this tops off a bit more energy. I'm very happy w/ charger. Do not use w/ alkalines (1.5V); NiMH are 1.2V as is the charger. Best wishes, sir.

Q: 2. Is it steady enough to hold a Nikon D3s + 70-200mm f2.8 or 200-500mm lens?My concern is especially if the tripod is steady enough at the center column not moving or shaking while panning.

A: Yes. I use it with my sigma 150-600 sport lens and it works great. It is rated for 33lbs. I think.

Q: 3. To unlock the legs, how much of a twist/turn is needed? One review says Gitzo only requires a turn and the Sirui a turn - is that a fair comparison?

A: The specification for the Sirui is 1/2 turn.

Q: 4. Is the bottom of the monopod a standard 3/8 size for adding a monopod base?

A: Yes it is 3/8

Q: 5. what voltage will the charger work with? 230 V will work?

A: Yes, this charger will work in 230v. It is a multi-voltage device and can work in any region, but would simply need a plug tip adapter to plug into non-USA outlets.

Q: 6. is there a 3/8 hole on the bottom?

A: The Gitzo GM4532 Series 4 Carbon Fiber Monopod has a 3/8"-16 screw on the base mount. The foot on the monopod is removable, and it has a 3/8"-16 thread size.

Q: 7. Did they stop putting rubber pads on the top threaded area? I sent the first one back because there was not pad, and the replacement is also missing a pad. Did I just get 2 bad ones in a row?

A: This monopod does not come with a rubber pad.

Q: 8. Can you put the three footed device on it!

A: Being that the foot at the bottom uses a 3/8-16" threading, the Benro 3-Leg Locking Base For Monopods, BH # BEVT2 would be something you can use. https://bhpho.to/2RCCWM4

Q: 9. How does one balance the load so that the tripod does not tip forward with the column fully extended horizontally?

A: You can balance the Manfrotto 190go! Carbon Fiber M-Series Tripod while using the horizontal arm by changing the length of individual legs, by how far you extend the arm, or by using weights, like sandbags, to balance the tripod.

Q: 10. Hi,Can I use this charger to charge my older WHITE Eneloop rechargeable batteries (1900mAh) too? Or is this charger to powerful for them? Thanks!Jan

A: The charger included with the above kit would be able to charge all Nickel Metal Hydride (Ni-MH) batteries, regardless of milliampere-hour rating. The charger would charge the older white 1900mAh Eneloop batteries.