The Dual V-Mount 6A Travel Charger from BLUESHAPE allows you to charge two V-mount batteries sequentially and features a 4-pin XLR power output. It's very convenient to use, featuring a carry handle and a rotating foot on the bottom for desktop use. This updated model of the CVTR2 charger allows you to use the XLR output as a UPS backup with a quick failover function, and it features a higher 6A simultaneous charge. It is also fanless to ensure a quiet charge. Batteries under 190Wh take less than two hours to charge, while batteries up to 290Wh can take a bit over four hours to charge to 100%.

The charger features a pop-out stand that neatly tucks away underneath when not needed. It can be powered via an included AC cable or the separately available BLUESHAPE In-Car Adapter. A data socket allows for a USB connection with a separately available 4-pin LEMO to USB cable to a computer in order to monitor charging activity and log battery data. The optional BLUESHAPE BSCVMON cable and maintenance utility are required for this, and up to four chargers can be monitored on a single computer.

This charger features a BLUESHAPE technology called IPCS (Intelligent Pre-Charge System) that allows it to provide charge at increased speeds to batteries with fast-charge supporting features, such as pre-charge protection and cell-balancing. IPCS does this by initially boosting very low voltage cells to a state at which charge can be applied with a medium-low current without causing damage. Then it charges with a 300mA current for a while, and when the battery reaches a reasonable voltage state, the charger speeds up the charging process by switching to full throttle. To counteract the increased heat caused by this fast-charging capability, the charger employs another BLUESHAPE technology called CTP (Charger Thermal Protection) that allows the electronics to work out the best possible charge profiles without causing damage, even in adverse temperature conditions.

2 x 193Wh Granite HDplus 14.4V Batteries    Dual V-Mount Travel Charger    Batteries Support up to 13.4A Draw    Charger Has 14.4 VDC 4-Pin XLR Output    Batteries Feature D-Tap Outputs

• 4-pin XLR power port can be used as UPS backup
• Fanless design
• Charge two batteries simultaneously at 6A
• Carry handle and extending desktop foot
• DC port supports optional BLUESHAPE in-car adapter
• Features a 4-pin data socket supporting optional computer maintenance utility
• IPCS/CTP fast charge and overheat features
• LED status indicator
• On/Off switch

Related Questions and Answers

Q: 1. looking to power a pair of westcott td6 spiderlights (600 watt draw). Will this do the trick, or do i need a larger battery. Any recommendations?

A: The Westcott Td6 is not a battery light and can only be used with a battery inverter.And if you are using a fluorescent lamps those can have issues with batteries in general.This inverter should be okay Dynalite XP800 Pure Sine Wave Inverter B&H # DYXP800 MFR # XP-800.But with hot lights if you are using those type of bulbs it will not last that long.

Q: 2. Hi just wondering whether this camera v-lock battery will fit a LightPro LED DN-900 HS? It has a v-lock plate on the back of the light. Wasn't 100 percent sure. Thanks

A: I think v-lock is a standard - a Sony one. It should work on your light.

Q: 3. Does this come with batteries?

A: Yes it comes with batteries.

Q: 4. can i replace my varicam GM PLATE to THIS MVFULL PLATE?

A: Yes, they have the same mounting holes.The connector in the back is a 2-pin TYCO MATE-N-LOCK.Please ensure you have a similar connector in the camera.Hope this helpsRegards

Q: 5. Can this be charged via the D-tap port?

A: It can be charged while attached to the light. I have not found a way to attach my d-tap charger directly to the battery.

Q: 6. Does the dracast battery work with a red one

A: There is no information stating this can work with RED camera protocols.

Q: 7. Can I power a Sony a7s and an Atomos Shogun recorder simultaneously through this plate with the correct cables?

A: Hello Andew,you can power a SONY A7s using oout BPA-021 adapter, that fits the blue socket (in this case, please ensure that the power selector in the back of the plate is on 7.4V).At the same time you can also power an ATOMOS SHOGUN using a D-Tap to D-Tap cable connecting it to the black lateral D-Tap adapter.The V-lock battery installed on such a plate will then power both devices.Hope this helps.Pietro

Q: 8. Does this battery not come with a charger? And if that is the case, do I really need to spend another $200+ on a charger (I see there is a dual charger recommended)?

A: There is a cheaper charger: https://a href= http://www.bhphotovideo.com/c/product/1166058-REG/indipro_tools_pd1013_pro_battery_charger_for.html/pageID/accessory target= _blank www.bhphotovideo.com/c/product/1166058-REG/indipro_tools_pd1013_pro_battery_charger_for.html/pageID/accessory/aIt's annoying that you don't get the charger with the battery - even more annoying that if you buy the Dracast 500 light panel kit, you get the battery and not the charger (but you do when you buy the 1000 kit). Which you don't discover until you try to use it on a shoot...

Q: 9. Could this be installed on the Blackmagic URSA Mini?

A: Matt, URSA Mini has a special connector to receive battery power.Although MVFULL can technically be screwed on the back of that camera, it has no means of ocnnecting to the URSA connector.Our MVURSA has that conenctor, ad is the correct plate to be used for that purpose.Hope this helps

Q: 10. Does this battery communicate with the RED cameras to show percentage/time remaining?

A: My Sony cameras show battery life with these batteries.