Protect your DJI Mavic 3 drone from the elements with the orange Nanuk 915 Waterproof Hard Case with Insert for DJI Mavic 3. This compact, hardened plastic resin case features a custom-cut foam interior with compartments for the Mavic 3 (with storage cover attached) and a variety of compatible accessories. There's room for one additional Intelligent Flight Battery, RC-N1 controller, a 65W portable charger, multiple cables, additional low-noise propellers, and spare control sticks.

Holds DJI Mavic 3 & Accessories    Custom-Cut Foam Interior    Made with Impact-Resistant NK-7 Resin    PowerClaw Latching System    Automatic Pressure-Release Valve    Foldable Soft-Grip Handle    IP67 Rated Water & Dust Resistance    Airline Check-In Compatible    Airline Cabin Carry-On Compatible

Crafted from NK-7 resin with a watertight seal, the case provides Mil-Spec rated damage resistance and IP67 rated water and dust resistance. Nanuk's PowerClaw latches securely close the case and further assist in sealing the case from the elements.

This built-in valve guards against the vacuum caused by changes in altitude and geographic location that tend to seal watertight cases shut. The pressure valve equalizes atmospheric pressure using micro vents, which allow air to pass through but prevent water from getting inside.

Foldable soft-grip handle
Airline check-in compatible
Airline cabin carry-on compatible

Related Questions and Answers

Q: 1. could this be used with the glide gear stabilizer vest?

A: Yes it can be. The Ronin-S is compatible with the Glide Gear DNA 6000 Stabilization System with Vest, Arm & Gimbal Adapter, BH #GLDNA6000VAO. https://bhpho.to/2FJgGoG

Q: 2. does it work with Leica Q?

A: It can easily handle it weight wise. The included USB cable should work as well.

Q: 3. Will it work with a Nikon D810?

A: Yes, you will be able to balance and shoot with the Nikon D810 on the Ronin-S. DJI is also working on support for functions with the D810 while shooting.

Q: 4. Is the DJI Ronin-S compatible with the Lumix dmc-gx8?

A: You will be able to balance and shoot with a camera like the Lumix DMC-GX8. However it is not on DJI's list of compatible cameras for electronic control at this time. https://bit.ly/2S6yT9s

Q: 5. How about with the Canon C200?

A: This Ronin is too small for the C200. Even if it took it, your hands wouldn't.

Q: 6. what is the minimum payload? can i use my canon m6 with the 22mm f2.0 lens?

A: DJI does not list minimum payload. It is our opinion that the Ronin S can fly the M6 and lens.

Q: 7. How will it hold up in a dusty environment? I understand is it not weather sealed (ie water resistant).

A: While the Ronin-S has no IP rating, there is not a lot of room for dust to get in to the motors. When in a non-optimal environment please limit exposure to the elements and try to clean your Ronin-S thoroughly to remove any potential debris.

Q: 8. can I use my canon c100 with this gimbal?

A: The DJI Ronin S has the payload capacity to stabilize the Canon C100 and lens but because of the design it's often easier to balance a 2-handed gimbal like the DJI Ronin M or MX with the C100. If you remove the side-grip and top handle the Ronin S should be a good fit after proper balancing.

Q: 9. Has anyone tried this with a z cam e2 f6 and if so how was it?

A: the DJI Ronin-S will work with the Z cam E2 F6

Q: 10. Will it fit/work with the new Blackmagic Pocket Cinema Camera 4K?

A: Hey Jasmine. Although further testing needs to be done to confirm compatibility, there is nothing about the Blackmagic Pocket Cinema Camera 4k that would fall within acceptable dimensions.