Protect your DJI Mavic 3 drone from the elements with the silver Nanuk 915 Waterproof Hard Case with Insert for DJI Mavic 3. This compact, hardened plastic resin case features a custom-cut foam interior with compartments for the Mavic 3 (with storage cover attached) and a variety of compatible accessories. There's room for one additional Intelligent Flight Battery, RC-N1 controller, a 65W portable charger, multiple cables, additional low-noise propellers, and spare control sticks.

Holds DJI Mavic 3 & Accessories    Custom-Cut Foam Interior    Made with Impact-Resistant NK-7 Resin    PowerClaw Latching System    Automatic Pressure-Release Valve    Foldable Soft-Grip Handle    IP67 Rated Water & Dust Resistance    Airline Check-In Compatible    Airline Cabin Carry-On Compatible

Crafted from NK-7 resin with a watertight seal, the case provides Mil-Spec rated damage resistance and IP67 rated water and dust resistance. Nanuk's PowerClaw latches securely close the case and further assist in sealing the case from the elements.

This built-in valve guards against the vacuum caused by changes in altitude and geographic location that tend to seal watertight cases shut. The pressure valve equalizes atmospheric pressure using micro vents, which allow air to pass through but prevent water from getting inside.

Foldable soft-grip handle
Airline check-in compatible
Airline cabin carry-on compatible

Related Questions and Answers

Q: 1. How about with the Canon C200?

A: This Ronin is too small for the C200. Even if it took it, your hands wouldn't.

Q: 2. Will the Ronin-S have a 3/8-16 screw mount on the bottom of it with an adapter for 1/4-20 like the Crane 2 does?

A: Yes, it has 1/4-20, 3/8-16 Mounting Hole, and M4 Mounting Hole.

Q: 3. Hi. I'm new at video and looking for a gimbal. Can this be attached to a monopod?

A: Yes, there is a threaded hole at the bottom of the gimbal for you to attach a monopod.

Q: 4. Will it fit/work with the new Blackmagic Pocket Cinema Camera 4K?

A: Hey Jasmine. Although further testing needs to be done to confirm compatibility, there is nothing about the Blackmagic Pocket Cinema Camera 4k that would fall within acceptable dimensions.

Q: 5. what is the minimum payload? can i use my canon m6 with the 22mm f2.0 lens?

A: DJI does not list minimum payload. It is our opinion that the Ronin S can fly the M6 and lens.

Q: 6. Will it have a manfrotto plate mount or dji plate mount?

A: The Ronin-S will be compatible with the E-Image EH6P Quick Release PlateB&H # EIEH6P. It will not be compatible with Manfrotto plates.

Q: 7. I have the new Ronin-s essentials with a Sony A 7III and can't get this thing to too stable to film in car. How can I fix this stability issue?

A: Balance is key to successfully operating this or any gimbal. Before shooting you must make sure that it is perfectly balanced as shown in the instructions for the gimbal. It will not be properly balance until when the unit is turn off and you turn the camera in any direction, it stays there. If you are properly balanced and still getting jerky movements when shooting in very fast situations, you may want to try the DJI Ronin-S External GPS Module B&H # DJGPSP21. This allows for better responsiveness to quick movements. https://bhpho.to/2KNVTGw

Q: 8. Will this work with sony a6300, mc-11 w/ sigma 18-35?

A: Yes it will. This gimbal has an 8 Pound Load Capacity. It will be able to handle that camera, adapter and lens combination.

Q: 9. Can the Sony PXW-Z90V work on the Ronin-S ?

A: Normally we have to just say no to camcorders. However, the PXW-Z90V is small enough that it might fit as well as balance. If it does, please report back what you have found out.

Q: 10. How do you connect the camera to the gimbal where the start/stop recording feature would work. Like, what cable or wireless connection is needed/included?

A: The Ronin-S comes with all the cables necessary to be compatible with the cameras on our compatibility list. More cameras will be added to this list in the near future.