Protect your mixer from the rigors of on-the-road wear and tear with the all-black Black Label Flight Case for Pioneer DJM-V10 Mixer. The flight case with black anodized powder coated hardware features a removable front-access panel, which provides access to the headphone connectors, while the interior utilizes a foam lining and provides plenty of space for ventilation and cable connectivity. The case has a butterfly latch and a recessed spring-loaded handle.

Removable Front-Access Panel    Recessed Handle and Latch    Ventilation Pit    Cable Ports    Stackable Lid    Limited Lifetime Warranty

• Black flight case with anodized powder coated black hardware
• Recessed handle and latches
• Removable front-access panel
• Heavy-duty ball corners
• Bottom interior ventilation pit
• Rear and bottom cable ports
• Foam-lined interior
• Rubber feet
• Limited lifetime warranty

Related Questions and Answers

Q: 1. Will it fit the Sony macro sel90m28g?

A: The case is a too small. This is a few options that will work.1.Ruggard Lens Case 6.0 x 3.5 (Black) B&H # RULCY16X3 MFR # LCY-16X32.Lowepro Medium Zoom Lens Case 9x16cm (Black) B&H # LOLP36979 MFR # LP369793.Mountainsmith Lens Case (Medium) B&H # MOLCMG MFR # 14-81270-65

Q: 2. Is the 6.0 x 3.5 large enough for a Zeiss 135mm ZF.2 APO, with the shade attached in the storage position? Thanks

A: I don't know if it will work with you lense, I use it for a differente one placing the hood on backwards when storing it the case.

Q: 3. Will it fit a Tamron 16-300mm lens?

A: May be a bit too big. The Lowepro Compact Zoom Lens Case 8x12cm might be a better fit - the Tamron 16-300 is approx. 7.5 x 10cm) from what I've read. The 8x12cm case leaves plenty of room for a filter. Haven't tried it myself though.

Q: 4. will a cannon 75-300mm lens fit?

A: Yes it will. This case will hold BH #CA753004EF3.

Q: 5. will this case fit a rokinon 85 mm lens?

A: What are the dimensions of your Ronkinon 85mm lens? If you measure them and they're smaller than the provided interior dimensions of the case then it will fit.

Q: 6. Would the Ruggard 3.5x3.5 fit the Zeiss Batis 25mm lens?

A: Zeiss lists the dimensions of the lens at 81 x 78mm (3.19 x 3.07 ) so I would say the lens would fit in the Ruggard case, with one caveat without the sunshade. I hope this helps. I really like the Ruggard cases I have.

Q: 7. Will this fit canon 35mm 1.4 ii?

A: Since I have not a Canon 35mm 1.4 ii, I can't be affirmative. But I have a Yongnuo 35mm, very similar. Lens fit well, including hood. Tight but not difficult to take out. Hoping it can help.

Q: 8. Will this case hold a Canon EF-S 55-250mm f/4-5.6 IS II lens?

A: I use this case for a TAMRON 70-300mm lens. With the back cover, UV protector, cap and a cap-keeper (elastic around lens with little button that sticks to the cap), my whole lens is 6 1/8 in. long. That fits, but it's a bit tight. I also keep the lens hood in the bottom which is fine because the lens fits through it. So, measure the length of your lens setup like you want it to go in there.This case has a mesh pouch in the lid which I can't use due to the length issue, but it could hold a battery, memory card or filter (but probably not in filter's original case) if you have a shorter lens.The interior diameter is 3-3 1/2 in. with good padding, almost 1/2 in. thick. My lens has plenty of room at just under 3 in. at widest point, still protected well. I have this case velcroed onto a matching Lowenpro zoom bag. Fits nice and tight, but the whole thing is a little unbalanced with no exterior pouch on the other side. That would be way too big for me. I compensate by wearing it cross-shoulder rather than in front with a chest or waste strap

Q: 9. Will the 6x3.5 case fit my Panasonic Lumix G-Vario 100-300 lens (67mm)with lens shade reversed? Will there be room on top for a filter? TIA

A: Yes, it does fit the Lumix 100-300mm, with the hood attached (reversed), and attached filter and front & rear caps; no issues.

Q: 10. Does the Nikon AF-S DX NIKKOR 18-200mm f/3.5-5.6G ED VR fit in this case, with the lens hood?

A: Yes, the lens hood needs to be inverted (as designed) to fit in the case.