This is a Photoflex Lamp - 500 Watts/120 Volts for Starlite QL - Mogul Base. This 3200° Kelvin tungsten-halogen bulb is for the Photoflex Starlite QL, Westcott Spiderlite, or Chimera Lantern fixtures.

Compatible with Photoflex Starlite QL, Chimera Lantern, Westcott Spiderlite

Related Questions and Answers

Q: 1. I want to use all my Bowens softboxes with profoto D2, is this ring compatible or any recommendation?

A: This ring is compatible with most softboxes.

Q: 2. what does it weigh?

A: The iFootage QL-I Quick Leveler weights 8.04 oz.

Q: 3. Or can i use s bracket mount for this?

A: you can use the softbox and rods. you'll need a bowens type speedring and the Godox S type adapter for Bowens

Q: 4. Are daylight bulbs available for these lights?

A: You can use the ALZO CFL Photo Light Bulb (85W, 120V) B&H # AL151255 and the Photoflex Mogul to E-27 Lamp Adapter B&H # PHFVSKT to fit into the Photoflex Starlite.

Q: 5. Whats its load capacity preferably in kilograms pls?

A: The following unit has a payload support of 23 lbs.

Q: 6. Would this fit an Octagon from Impact on my Profoto strobe head?http://www.bhphotovideo.com/c/product/889690-REG/impact_lb_od_l_luxbanx_duo_large_octagonal.html

A: Yes, the Photoflex Speed Ring for Profoto, B&H # PHSRODPF, would allow you to attach the Impact Luxbanx Duo Large Octagonal Softbox (84 ), B&H # IMLBODL, onto Profoto strobe heads.

Q: 7. This speed ring works with a photoflex Small Half Dome?

A: Yes, the Photoflex Speed Ring for Dynalite may be used with the Photoflex Small Half Dome nxt with Silver or White Interior.

Q: 8. can the base separate?I would like to confirm if on this unit, are the 4 screws at the bottom of the base that are shown in the photo, is it possible if those were loosen, that I could then detach the black rubber neck piece, resulting in having 2 separate pieces?I have a older Photoflex Octobox that I use with another strobe, and when I mounted my octobox to those strobes there was a plate that appears to look just like the one in this photo but it does not have that wide base part with the 4 screws, which is where the rods connect to.I have the D2 profoto now, but i just need the speedring that will slide onto barrel of my profoto and the other end will be the thin, flat, round plate that I would connect to my octobox and tighthen down with the 4 screws it has.So if I could verify that this item could be separated into 2 pieces, this might be what I have been looking for?

A: The center ring and the outer ring can be detached from one another, however if you just need the center ring for a custom set up, we also offer the Profoto Adapter Plate for Custom Made Reflectors to fit Profoto Flash Heads B&H # PRAPR. Please see the image below.

Q: 9. How badly does the umbrella shaft interfere with the thumbscrews?

A: I have never found that to be a problem...

Q: 10. Will this work out of the box with a sony a7riii?

A: The Photoflex Portable Speedlite Kit does not include speedlites, but you can add the Godox TT685S Flash Kit for Sony, BH # GOTT685X2TS and the Godox TT685S Thinklite TTL Flash for Sony Cameras, BH # GOTT685S which is compatible with the A7R III. https://bhpho.to/3a1ewVO https://bhpho.to/3NJKXXD