The Xdirect from ART is a high quality interface that allows for connecting instrument, line, or speaker level signals to a mixer or other balanced input. The high impedance single-ended 1/4" and XLR inputs are buffered and converted, by very low noise active electronics, into an isolated balanced low impedance signal source.

The unit has an extremely flat and wide frequency response and can handle high signal levels while still maintaining an isolated balanced low impedance output. This gives the Xdirect a very clean and neutral sound with a wide variety of signal sources and over long signal runs in high noise environments.

The Xdirect's active circuitry is powered by an internal 9V battery, when external power is not available. In this mode it draws 3.5mA which should provide more than 250 hours of operation off of a new battery. If phantom power is available, then the unit will automatically draw its power from the external source.

Active    Battery or Phantom Powered

The input attenuator switches allow for a wide range of input signal levels

The Input Link jack allows for tapping off of the signal chain for additional routing

A ground lift switch allows for totally separating the input and output signal grounds when appropriate, to isolate two systems thereby reducing hum and ground-loop noise

Switchable low pass filter cuts out all very high frequency interference. This Bessel filter on the input is placed out of the audio range and is primarily intended to reduce radio frequency interference before it gets into the main system

The filter is also very effective in reducing any digital computer noise artifacts when using the Xdirect as an interface between a computer based audio workstation and speaker monitors

A phase invert switch allows the user to switch signal polarity right at the source

The compact black anodized all aluminum case and its flexible power design allow the DI to provide years of trouble free service in live sound, fixed install, DJ and virtually any PA application

Related Questions and Answers

Q: 1. What is the largest circular filter size allowed for by the female threading on the adapter ring? Would it be possible to use an 82mm filter with a 77mm step down ring to attach to the adapter ring to use inside the matte box for example?

A: According to Tilta 85mm would be the largest. A 77mm to 82mm step up ring would allow you to use the 82mm clamp on attachment with an 82mm filter on a 77mm lens.

Q: 2. Will 2 Profoto A1's work with this...

A: This product is just the plate (I think), they'll likely work with the Rapid Box Duo but you'll have to get your ruler out and maybe contact Westcott. I can say however it's a top shelf piece of kit.

Q: 3. Does it work with octa-m rapid box?

A: Yes, the following item will work with the octa-m rapid box.

Q: 4. Will this matte box fit a Sigma 24-70mm zoom lens?

A: That will depend on the exact model of Sigma 24-70mm lens you have. That being said this systems comes with 67mm. 72mm, 77mm and 82mm adapter rings. If you have the Sigma 24-70mm f/2.8 DG OS HSM Art Lens for Canon EF that lens has an 82mm filter thread and will work with this matte box. You will just need to double check the exact model you have and see what filter thread it offers.

Q: 5. Will this work with Godox AD600 Pro?

A: Yes. But the following cookie is needed in order to do use. Westcott Rapid Box Switch / Beauty Dish Switch Insert for Bowens Flash Heads BH #WE2530 • MFR #2530 https://bhpho.to/2vyTVRR

Q: 6. Will this fit a Bowens mout s type

A: Yes, The Rapid Box Switch series has options for 13 different light mounts, including the Bowens-S. That insert can be purchased using this link - https://www.bhphotovideo.com/c/product/1414215-REG/westcott_2530_rapid_box_switch.html?sts=pi&pim=Y

Q: 7. I lost the bolt for this, can I buy just that?

A: Replacement parts can be obtained from Westcott directly. Please follow the link to their parts page: http://bit.ly/1gaibz7

Q: 8. Does anyone know the length of this collapsed?

A: When collapsed, the Westcott Rapid Box Switch Softbox 3 x 4 measures 33 inches long.

Q: 9. Does it work with ledgo fixtures?

A: The Nanlink Transmitter box compatible with the following Nanlite lights... esigned For Use With: Nanlite Compac 200 Nanlite Compac 200B Nanlite FC300 Nanlite FC500 Nanlite FS-150 Nanlite FS-150B Nanlite FS-200 Nanlite FS-200B Nanlite FS-300 Nanlite FS-300B Nanlite FS60B Nanlite Forza 150 Nanlite Forza 150B Nanlite Forza 200 Nanlite Forza 300 Nanlite Forza 300 II Nanlite Forza 300B Nanlite Forza 300B II Nanlite Forza 500 Nanlite Forza 500 II Nanlite Forza 500B II Nanlite Forza 60 Nanlite Forza 60 II Nanlite Forza 60B Nanlite Forza 60B II Nanlite Forza 720 Nanlite Forza 720B Nanlite Halo 16 Nanlite LumiPad 11 Nanlite MixPad 27 Nanlite MixPanel 150 Nanlite MixPanel 60 Nanlite PavoTube 15C Nanlite PavoTube 30C Nanlite PavoTube 6C Nanlite PavoTube II 15C Nanlite PavoTube II 15X Nanlite PavoTube II 30C Nanlite PavoTube II 30X Nanlite PavoTube II 60X Nanlite PavoTube II 6C

Q: 10. are there spacers to allow this to clamp on to 80mm fronts?

A: The SmallRig Mini Matte Box Pro does not have a 80mm adapter.