The Mackie C300Z is a mid-priced 2-way speaker with a 12" woofer and a 1.75" compression driver housed in a wide-dispersion constant directivity horn, with a 300 Watt average power handling capacity.

The asymmetrical design and internal damping of the C300Z contribute toward a natural sound reproduction free of phase anomalies, and the rugged enclosure may be pole-mounted, flown, or used as a floor monitor. C series speakers are tuned exclusively by the renowned EAW design team, and offer design concepts applied to elite loudspeaker systems at a fraction of the cost.

Portable Passive loudspeaker with 1.75" HF compression driver and 12" LF transducer

750W peak power handling

HF compression driver mounted on multi-celled aperture, with constant directivity horn for wide 90° x 45° dispersion angle

Accurate reproduction of upper mid-range and high frequencies, tuned Low Impedance Compensated Crossover(LICC) for matching driver beamwidth patterns

Asymmetrical monocoque design with no parallel surfaces, causes reflection of mid and high frequency resonances at angles into internal damping materials, minimizes phase anomilies and other signal distortion

Equally viable as floor monitor or mounted/flown PA speaker with natural frequency response and dispersion, free from feedback-causing transient spikes

Dynamic protection for compression driver, 2nd order high-pass filter for over-excursion protection

Inputs and thruputs for parallel connection of up to 2 sets of speakers from single amp channel or powered mixer

Rugged impact-resistant enclosure with sturdy side handles, pole-mount, and integrated rigging points for "flying" the speakers

Related Questions and Answers

Q: 1. is this remote compatible with the Nikon D300S?

A: If the 300 S is a 10 pin then it will fit.

Q: 2. Is the ML-3 compatible with the Nikon F6?

A: No, it is not listed as compatible via the information we've received from Nikon and listed on our site. If you would like more details please contact Nikon for additional information.

Q: 3. Can you change the camera settings through this remote?

A: No this is just a trigger

Q: 4. Can a tilt and pan head be placed onto this tripod? Like a Manfrotto 502AH head?

A: Yes the head on the GEEKOTO AT24EVO Compact Aluminum Tripod can be removed and replaced with a different type of tripod head.

Q: 5. Is this pouch U.S.A made?

A: Yes. Domke is the only brand which is still made in the USA. And such is their quality.

Q: 6. Is this too small for Nikon z8 with 14-120? Need purely for videos on Manfrotto 190prob tripod.

A: The SmallRig CH10 Compact Fluid Head will still be under its payload with the NIkon Z8 and 24-120mm f4 lens. It is a great solution for small kit needs for video.

Q: 7. Does the ball head tilt to 90 degrees?

A: Certainly! :)

Q: 8. is the plate the same or compatible with Dji Ronin SC?

A: The plate form the SmallRig CH10 Compact Fluid Head is compatible with the DJI Ronin SC.

Q: 9. I have a Benro Tad37c adventure tripod. Will this head work on it and would it be sufficient for a spotting scope?

A: No, The SmallRig CH10 Compact Fluid Head has a 1/4 20 and your tripod has 3/8 connections for video heads. You could use an adapter to mount this head to the Benro tripod like the following. CAMVATE 3/8"-16 Female to 1/4"-20 Male Tripod Adapter BH #CAC2739 https://bhpho.to/3GqJ9AS

Q: 10. Does it come with lens and camera mounts? (Canon R)

A: The Novoflex Universal Compact Bellows would be the bellows by itself. The Novoflex Universal Compact Bellows, B&H # NOBALF, does not come with a camera mount or lens mount adapter. These must be purchased separately. You would need 2 pieces to mount the camera. The Novoflex A-Mount to BAL-F Adapter Ring linked here. https://bhpho.to/2W8tHpq. And the Novoflex Universal Bayonet A Adapter Ring for Canon RF Cameras linked here. https://bhpho.to/3BrAfzs. The proper lens mount will depend on the lens you wish to use on this.