The Kalt Camera Strap is a cotton camera strap with a width of 2" and snap hooks that attach to your camera. The length can be adjusted from 21" to 43.7".

Note: Actual color and pattern may vary.

Adjustable 21-43.7" Length    Cotton Strap, 2" Width    Snap Hooks Attach to Camera    Pattern & Colos May Vary

Related Questions and Answers

Q: 1. Does it work on canon r5 with battery grip attached?

A: The Peak Design CL-3 Clutch Camera Hand Strap is compatible with the Canon R5 with a battery grip attached.

Q: 2. Can the single holster be used on left or right side?

A: Yes, The simplest method is to rotate the belt so that the clip is on the other side.

Q: 3. Do all the dividers and accessory sleeve shown in the photos come standard with the bag?

A: Yes ( In the Box Tamrac Stratus 21 Shoulder Bag (Black) Shoulder Strap Foam Padded Divider Limited 5-Year Warranty )

Q: 4. Other than the ones shown in photos, How many dividers come with this bag?

A: There are 9 dividers in total for the Tamrac Stratus 21 Shoulder Camera Bag.

Q: 5. Is this safe to hang with heavy lenses mounted to your camera without damaging your lens mount on the camera? I'm just thinking of the 70 - 200 2.8 is

A: I use the SpiderPro single-camera holster with a Nikon D800 and 80-200mm f/2.8AF-D. That all-metal lens measures roughly 7.5 in long x 3.4 in diameter, and weighs 3 lb.; the camera body adds 2 lb. I have not discovered any stress to the body lens mount, although I can imagine that the torque induced by this relatively heavy lens can be considerable, even as one merely walks about. My experience (and my hunch) is that the camera can take it. That said, one must be constantly aware of one's wider girth when using the SpiderPro and bulky camera gear. Smashing into narrow doorways or ship's bulkheads or rocky outcroppings will greatly exacerbate the torque I mentioned earlier and could lead to camera mount damage or more. Be careful and enjoy the freedom the SpiderPro brings. I rely on it when using hiking poles and depend on it when my hands have to be free. Good luck!

Q: 6. Can you tell me how long the silver legs are? Can the ballhead, along with the tighten screw housing be removed ? How long is the shaft, from the legs to the tighten screw? What is the diameter of the shaft?

A: When extended, the silver legs are slightly over 3 3/4 from the body each. The bullhead itself cannot be removed, but the top part of the housing unscrews from the tube, as well as the bottom part of the housing that is the leg support. The shaft itself is 1 diameter; the top housing is 1 1/8 ; the bottom housing is 1 1/4 . With the legs extended, the length from the tabletop to the top of the tightening nut that tightens against the camera body is 7 5/8 .

Q: 7. Please list every component in the box so I know if I need to purchase accessories?

A: Our product pages have their individual component items listed in the overview in the section titled "In The Box". For your convenience: In the Box : Peak Design CL-3 Clutch Camera Hand Strap Standard Plate 2 x V4 Anchor Links Limited Lifetime Warranty

Q: 8. Will this work while I have a the Peak Design Capture Camera Clip v3 QR plate attached?

A: Yes it will still be able to take the clutch when using the capture system.

Q: 9. How long are the silver legs? What is the diameter of the shaft? Can the top, where the tighten bolt (under ball) be removed?

A: The silver legs are approximately 3 and 3/4 inches when they are in position on the desk the diameter of the Shaft is approximately just around 7/8 of an inch the whole top section is removable as one piece from the shaft.

Q: 10. Any idea on how to keep the legs from sliding out so easily?

A: Sorry, there is no way to tighten the legs nor is there an accessory available that will keep them in tighter.