The Redrock Micro flexCable for the microRemote Fingerwheel lets you connect the microRemote Fingerwheel to the microRemote Basestation. This 24" version is designed to allow the camera operator to pull focus from the Fingerwheel. It features a 3-pin connector on one end and 5-pin on the other.

Connect Fingerwheel to Basestation to Pull Focus from Fingerwheel

flexCables are 35% lighter than most standard cables thanks in large part to the cable sheathing that's ultra-lightweight (yet still provides the required protection).

flexCables have a 200% greater flexibility than most standard cables, allowing for less drag and easier cable wrangling. These cables can be wrapped, twisted, and bent to keep your rig tight without damaging or crimping the cable.

flexCables are 20% thinner than most standard cables. You can more easily install them where you need to and secure them with less effort.

Related Questions and Answers

Q: 1. I want to use this on the Dji Ronin M, What else do I need to buy to make this work? Just a Ptap Cable to power it from the Ronin M? I basically want to be able to be a single operator with the thumb controller. Where Can I find out what all I need to make this work. I live in South America and do not want to have to order some other part after the fact. Thanks for any information as I am looking for a solution for one man operation with a ronin m, a7sII an Loxia lens. I know I need the gear straps for the lens, but is there anything else I need? Extra plates,arms or anything for the ronin to get this set up and work, Plan on using a smallhd502 on the ronin handles. Thanks for any information.

A: Hi EricThere's a lot of ground to cover there. what I recommend is picking up the remote fingerwheel bundle without cables, and get the DJI specific cable pack:a href= http://www.bhphotovideo.com/c/product/1140914-REG/redrock_micro_8_114_0011_microremote_handheld_fingerwheel_bndle.html target= _blank http://www.bhphotovideo.com/c/product/1140914-REG/redrock_micro_8_114_0011_microremote_handheld_fingerwheel_bndle.html/aa href= http://www.bhphotovideo.com/c/product/1111304-REG/redrock_micro_8_100_0007_dji_ronin_microremote.html target= _blank http://www.bhphotovideo.com/c/product/1111304-REG/redrock_micro_8_100_0007_dji_ronin_microremote.html/afor mounting the motor, you'll want the rhino mount, probably 4 a href= http://www.bhphotovideo.com/c/product/1176779-REG/redrock_micro_2_167_0002_rhino_mount_shoe_mount_clamp.html target= _blank http://www.bhphotovideo.com/c/product/1176779-REG/redrock_micro_2_167_0002_rhino_mount_shoe_mount_clamp.html/afor lens gears, you might be best to go with a kit that covers all possible lens sizes (though loxia are typically A or B sized lens gears)a href= http://www.bhphotovideo.com/c/product/748784-REG/Redrock_Micro_8_003_0107_microLensGears_Kit_4.html target= _blank http://www.bhphotovideo.com/c/product/748784-REG/Redrock_Micro_8_003_0107_microLensGears_Kit_4.html/aFor mounting the 502 monitor, you can look at the billie ball mount as a low profile ball mount that attaches to the DJI accessory platea href= http://www.bhphotovideo.com/c/product/970766-REG/redrock_micro_2_138_0001_billie_ball_mount.html target= _blank http://www.bhphotovideo.com/c/product/970766-REG/redrock_micro_2_138_0001_billie_ball_mount.html/ahope that helps

Q: 2. Will this work with the Zacuto Gratical Eye?

A: Yes, Its workink

Q: 3. are both connectors Pin-1 +VDC? Thank you.

A: If I understand your question, you want Pin-1 to be +VDC. The answer then would come from what power source it is connected to. If that is Pin-1 +VDC, this would be as well.

Q: 4. Hello there. Can I use this cable to power my Zacuto Gratical EVF? THX

A: That would depend on what power you are using. This question is better answered directly. Please email us at provideo@bhphoto.com.

Q: 5. Is this 3pin lemo connector compatiple with the 3 pin lemo port on the Steadicam Zephyr which is an 12-24v EGG-0B-0303?

A: Hi JB - thanks for asking. This cable is designed for the powerPack to power barrel connector devices such as compatible smallHD monitors.I think we saw a similar question coming from you earlier, so if you are looking for a custom cable you might drop us a line directly and see if we can solve your problem.

Q: 6. Does this have the LEMO FGG.0B.301 male connectors?

A: Unfortunately, Redrock Micro does not provide information on how their 7-Pin LEMO to 7-Pin LEMO flexCable is constructed. It is specifically made for use with their microRemote Torque Motor.

Q: 7. will the thumbwheel mount onto the Movi Pro ring?

A: HI Derekyes, you will just want to add the universal clamp adapter and you are good2-136-0002 Collins Clamp microRemote Fingerwheel Upgrade $85

Q: 8. How can you change the focus throw?? I get how to change Gain/smoothness but want to adjust the throw. At the moment, if you turn the Remote only a few millimetres it will focus the lens quite extremely. I hope that makes sense!?

A: Hi Dane - the microRemote has 270 degrees of throw which should be more than enough for almost any lens (with the exception of macro lenses that have )you can manually calibrate to a portion of the lens' throw so you can get even more granularity for shots that have limited range. If you are looking for additional support and you own a microRemote please contact our support group at support@redrockmicro.com - they can offer more assistance there. Thanks

Q: 9. Will this power the Red Komodo and Cine 7?

A: The Red Komodo and the SmallHD Cine 7 both have a 2-pin LEMO power connector, so in theory it should work. However with out testing I cannot confirm. This cable is described to power an optional Redrock microRemote.

Q: 10. Will this kit be shipping with the Flex cables?

A: It is a new item so we cannot confirm at this time but we feel confident that what you see is what you will get including the three cables.