The Tiffen 3 x 4" 1 Green Hard-Edge Graduated Filter helps to specifically add a bright green coloration to skies and other bright areas of an image while allowing a portion of the image to remain neutrally colored. The filter's coloring is densest at the edge and tapers to clear by the middle, with a hard-edged transition between the density and clear areas. The 1 color density provides less green coloration than the 2 density filter.

This filter is made using ColorCore technology, a process that involves laminating the filter substrate between 2 pieces of optical glass and grinding flat to a tolerance of 1/10,000th of an inch. It measures 3 x 4" / 76.2 x 101.6mm.

Note: A horizontal orientation filter's line of transition runs parallel to the long side of the filter.

1 Density Color Graduated Filter    Green Coloring in Select Areas    Hard-Step Graduation    ColorCore Technology

Provides a bright green coloring to select areas of the image.

Graduated filter design keeps a portion of the image neutral, resulting in a more realistic look while allowing for the sky or other bright areas to take on the color of the density.

Related Questions and Answers

Q: 1. Will this work for A7iii?

A: SmallRig Rotatable Horizontal-to-Vertical Mount Plate Kit for Sony a7R IV, a7R V, a7 IV & a7S III is not compatible with the Sony a7 III Mirrorless Camera. You can consider Silence Corner Atoll S Rotating Camera Collar for Select Sony Mirrorless Cameras (Silver) BH #SISCATOLLS https://bhpho.to/3nGfzSh.

Q: 2. Can I mount a Sony PXW-Z90 V cam corder on the Ronin S and still have the tilt functions work? The camcorder is 7.5 inches from the front of the fixed lens to the back of the battery.

A: Based on the size dimensions and weight specifications on the camera, it should work fine. I have seen a RED Epic w/battery and Canon 24-70 work, and while smaller in size, the weight is much higher and the motors were able to compensate with some adjustment on the Ronin app. I would take time to set up the proper tilt speed on the Ronin app if longer weight distribution effects the tilt motor performance. The primary limiting dimension for mounting cameras on the Ronin S would be width, (Cannot exceed Approx 6 or so?) and weight. While weight can't be fixed necessarily (is still able to hold beyond suggested payload) Width can be compensated using an additional wide slider plate attachment

Q: 3. Can the Canon T3i with Canon lens EF 75-300mm f/4.0-5.6 & lens EF-S 10-18mm f/4.5-5.6 be used on the Ronin-S?

A: The longest telephoto lens that DJI has tested to work with a Canon camera on the Ronin-S is 85mm, the 75-300mm may not balance properly. However the 10-18mm should balance fine with the T3i on a Ronin-S.

Q: 4. Windshield SPECS say Maximum Microphone Length: 6.25 (160.5mm) but NTG2 SPECS say 10.94 x .87 (278 x 22mm) (Length x Diameter) PLEASE clarify because I just placed an order ?

A: I wish I could post the picture I just took. The Windshield fits perfectly on the NTG2. 10.94 is including the section I would call the handle .

Q: 5. How much better is this versus the windshield that comes with the rode videomicro already?

A: This windshield is identical to the one that comes packed with the Rode videomicro. Don't buy the windshield separately like I did.

Q: 6. What's the difference between this and the dead wombat that comes in the blimp kit? Is one better than the other.

A: I literally have both. This works well when the wind is now point towards the direction of the wind.For near silence, go with a blimp. Added wombat shield is absolute noise reduction. This is great if you can only afford this. But TBH, id save the difference and get a Rhode.

Q: 7. Does it work with the Sony a7r iii?

A: The gimbal supports the weight of the A7Riii if that is what you are asking. It does NOT support the focus control knob for manual focus pulling. It does however support triggering of the shutter/video with an infrared cable supplied with the Ronin.

Q: 8. Can this fit on the Sony A1 if you take out the Anti-twist Pin?

A: The Anti-twist Pin does not come off, but this item does fit the A1.

Q: 9. If the base is fixed, how can you pan? Is that base Arca Swiss compatible? Why was the pan base discontinued?

A: The Really Right Stuff PG-01 Pano-Gimbal Head with Lever-Release Clamp and Fixed Horizontal Base has an Arca plate which could be connected to a Really Right Stuff panning clamp or a Really Right Stuff ball head with a panning position.

Q: 10. Fits on the A7IV with the SmallRig Cage Rinoceros on it?

A: No the SmallRig Rotatable Horizontal-to-Vertical Mount Plate Kit for Sony a7R IV, a7R V, a7 IV & a7S III does not fit with the SmallRig Rhinoceros Basic Cage Kit on it.