Protect your 3D printer and prevent debris from interfering with your process using the Creality Large Size 3D Printer Enclosure. Derived from high-quality aluminum foil with flame-retardant materials, the enclosure can properly manage heat levels to reduce the impact of lower external temperatures for optimal printing. Easily construct and take apart the enclosure thanks to the simplistic iron pipe supports and 3-way corner connectors. With the tight zipper head, you get quick access to the inside, allowing you to quickly monitor the status and remove your prints when finished. The 35.4 x 29.5 x 27.6" size allows you to fit a variety of smaller Creality printers including the Ender-2, Ender-3, Ender-5, CP-01, CR-100, and more.

35.4 x 29.5 x 27.6" Size    Aluminum Foil with Flame Retardant    Iron Pipe Skeleton    Waterproof Design    Zippered Enclosure

Related Questions and Answers

Q: 1. Hi, what is the difference between this OWC Thunderbay 4 enclosure and this other one that you have on your website (https://www.bhphotovideo.com/c/product/1635299-REG/owc_owctb3ivkit000_thunderbay_4_0tb_4_drive.html/overview) ?

A: BH #OWTB3SRKT0GB comes with the SoftRAID controller software included, while BH #OWCTB3IVKIT0 does not. Apart from this difference they are the same item.

Q: 2. How much does it cost to How much does it cost to upgrade to "SoftRaid" software to do all RAID configurations?

A: SoftRAID Software would be included with this product.

Q: 3. Is TB3 support Power delivery to MBP?

A: There is only 15W available, so in effect there is no power delivery.

Q: 4. Is there a way to connect a mac without a Thunderbolt port to this?

A: No, the only connection for any computer to this hard drive is thunderbolt. No other connection.Haile Okbe, Toronto, Ontario, Canada

Q: 5. I purchased one of these units - along with 4x16TB 3.5inch drives, and am running this in Raid 5. I have filled up the drives and just wandering - Can I purchase 4 new drives and set it up as a fresh Raid-5, but still have the option in the future to plug back in my old drives and access the data? Will the enclosure recognise previously created volumes?

A: In order to create a new RAID setup with the OWC ThunderBay 4 4-Bay Thunderbolt 3 RAID Enclosure, you will need to purchase the SoftRAID XT software from OWC. That will allow you to have a new RAID setup. But when you put in the old drives, the enclosure will recognize the old drives. Make sure that you number the drives and input them in the same bay as removed.

Q: 6. why the money back to the card returned a week after the payment ?i ordered a hard drive (472$ owc )i am from Kazakhstan,i wrote my address,can you make shipping for Kazakhstan?

A: I apologize, but this type of request cannot be taken care of through this feature of our website. Please contact our Customer Service department by entering Live Chat, emailing directly to cs@a href= http://bhphoto.com, target= _blank bhphoto.com,/a or calling us toll-free at 800.221.5743.

Q: 7. Can it handle 4 x 14TB hard drives?

A: You could use 14TB drives with this enclosure.

Q: 8. Will this work with 4 Seagate 22TB IronWolf Pro 7200 rpm?

A: Yes, you can use four Seagate 22TB IronWolf Pro drives in the OWC ThunderBay 4 4-Bay Thunderbolt 3 RAID Enclosure.

Q: 9. Can I install 2 8 tb & 2 3 tb drives and have Raid 1 on each of them seperately? Which version do I need? Can I move over from an old OWC Thunderbolt 2 enclose the hard drives that are set as RAID 1 and 2 new drives of 8 tb but one has DATA & the 2nd 8tb is pending for the Raid 1 setup.

A: You can have two different RAID families in this box, however moving drives from another box with a RAID family already configured may not be compatible.

Q: 10. what is the warranty for this device (box AND drives)?

A: This product has a Limited 3-Year Warranty.