Drive power to your system with the robust 1000W C1000 Gold ATX 3.1 Computer Power Supply from NZXT. Designed for high-end gaming builds and workstations alike, the C1000 boasts immense wattage to handle a variety of demanding tasks while balancing throughput, optimizing power and efficiency.

Equipped with a single +12V 1000W rail and meeting ATX12V version 3.1 compliance, you get ample power to operate your resource-demanding components. Thanks to the modular form factor, you can pick and choose the cables you need for your system, saving space and leaving ample room for airflow. Traditional 24-pin, 4+4-pin, and 8-pin motherboard connectors are included alongside the 12 SATA and four peripheral connectors for your storage drives and devices. Supporting graphics cards are three 6+2-pin PCIe connectors while one 16-pin 12VHPWR connector is reserved for high-powered NVIDIA 40 Series graphics cards, sending a dedicated 600W to the GPU.

1000W Single +12V Rail    135mm Fluid Dynamic Bearing Cooling Fan    Intel ATX12V Version 3.1    1 x 12VHPWR Connector    3 x 6+2-Pin PCIe Connectors    12 x SATA Connectors    4 x Peripheral Connectors    Modular Cable Design    80 PLUS Gold Efficiency

Backed by the 80 PLUS Gold rating, you can ensure the C1000 operates at maximum efficiency with up to 91.9% and 89.3% at half and full loads, respectively. This ensures that your energy and power consumption isn't wasted.

Inside the metal housing of the power supply is a 135mm cooling fan equipped with magnetic levitation bearings for a smooth and fast operation that keeps the capacitors well within thermal range. This fan operates at a max speed of 2300 rpm with 93.02 CFM airflow while retaining a low-noise level of 44.5 dBA at max load, ensuring enhanced cooling while remaining quiet.

Measuring 6.2-inches in length, the C1000 can easily fit in a variety of cases both big and small without sacrificing performance.

Related Questions and Answers

Q: 1. I am using this to convert SDI from PTZoptics camera into ATEM Mini Pro. getting no signal. Thoughts? Camera works fine with straight HDMI cable but want a longer distance, so SDI was solution.

A: Some of these cameras will work at 30 FPS and lower but at higher frame rates do not output a standard SMPTE SDI signal. This may or may not be the cause. You might contact support in your region.

Q: 2. Can i send different signals to sdi and hdmi in, and have those two signals out, simultaneously?

A: No, the Blackmagic Design Micro Converter Bidirectional SDI/HDMI 3G (with Power Supply) does not support the intake of two sperate video feeds. It can only support one feed at a time, but it can output that feed via both outputs.

Q: 3. Does the mini converter add any delay? Signal path is Camera to SDI output to mini converter to HDMI output to monitor. Will the hdmi output on my monitor be in sync with the real time action in front of the camera?

A: The Blackmagic Design Micro Converter SDI to HDMI 3G will add less than a frame of delay, but HDMI monitors will have it's own delay in processing and displaying. You can expect a delay of about a couple of frames. Delay more than 2-3 frames will be noticeable.

Q: 4. Is the sharpness of the lens good for architectural photography? is the tamron lens better than this?

A: The Tokina 11-18mm f/2.8 ATX-M Lens (Sony E, White) is a good lens. But there are ones that are much sharper. The Tamron is a little sharper.

Q: 5. Good day, can I use these to convert an SDI program output from a Blackmagic ATEM 4K Switcher to HDMI so I can input that into an Intensity Shuttle?

A: No. The HDCP support will black out the signal when it is routed to another processor instead of a display.

Q: 6. Does anyone know what is the length of USB-C power cord? From the product picture, power cord is not replaceable so I would like to know the length otherwise I may have to go with the non power cord version and get my own USB-C power cord and adaptor.

A: It's about 59 inches long.

Q: 7. Can some of you please confirm that THIS UNIT will allow me to connect a BMD Studio 4K (SDI) to an ATEM Mini (HDMI) ... with CAMERA CONTROL (CCU)? Thank you!

A: As long as the firmware is updated, it will work.

Q: 8. Can this be used on Sony a6000?

A: Yes, the Tokina 11-18mm f/2.8 ATX-M Lens (Sony E, White) is compatible with the Sony A6000.

Q: 9. Will this work with the ATEM Studio Pro HD and a PC for streaming?

A: The Micro Converter has nothing to do with connecting to a computer or streaming. You could consider the Ultrastudio Recorder 3G.

Q: 10. Does this work with the BMD Studio Micro camera control. The same way as with the Pocket cameras?

A: At the moment it does not. This will be addressed in a future update.