The Kopul Premier Quad Pro 5000 Series XLR M to XLR F Microphone Cable 6' is a studio- and broadcast-quality 4-conductor cable precision engineered for maximum rejection of RFI and electro-magnetic interference, extremely quiet performance, high flexibility and durability. Its twisted quad-conductor design features oxygen-free copper and allows for excellent conductivity, flexibility, low capacitance, and tensile strength.

This design affords the conductors a twist pitch length of only 0.7", reducing interference by assuring the minimum amount of the conductor is parallel to interference sources at any given section. The result is increased rejection of electro-magnetic and RFI noise, even in close proximity to the source. Cotton yarn is packed in to reduce friction between conductors and prevent unwanted electrostatic build-up and microphonic noise. The 99% braided TAC shield provides additional noise protection and corrosion resistance. Its Neutrik XX gold connectors provide high-quality, corrosion-free connectivity, and each solder point is individually shrink-wrapped for additional protection and to meet network broadcast facility standards.

Premier Quad Pro 5000 Series cables are ideal for use in the most demanding studio, touring, and broadcast applications.

For Most Demanding Studio/Broadcast Use    Neutrik XX Gold Connectors    4 Conductor Design    99% High-Density TAC Braid    24-Gauge OFC Conductors    .7" Twist Pitch Length for RFI Rejection    Cotton Yarn Wrap Reduces Noise    Shrink-Wrapped Solder Points

Precision-engineered twisted quad-conductor design

0.7" pitch twist length for greater induced noise reduction

99% tinned copper braided shield for long-lasting protection against RFI and EMI

Ultra-low capacitance for accurate signal reproduction

Cotton yarn to reduce electrostatic and microphonic noise

Shrink-wrapped solder points for extra protection

Ideal for broadcast and audio professionals

Related Questions and Answers

Q: 1. Do these adapters fit properly in Neutrik XLR jacks (used in Sound Device MixPre-6 II field recorders) or do they get stuck?

A: Yes, the Kopul XLR Twist-360 Angled XLR Adapter is compatible with Neutrik XLR jacks.

Q: 2. How is this adaptor wired? We assume BNC "hot" goes to XLR pin 2, but is XLR pin 3 floating or strapped to XLR pin 1? Can we alter the internal wiring?

A: According to Neutrik, the NA2FBNC is wired so that XLR pin 2 is hot and pins 1 and 3 are wired to ground. The internal wiring on the adapter is not intended to be reconfigured. For more information about the wiring, please contact Neutrik directly. Their US office is located in Charlotte, NC and you can reach them by phone at 704-972-3050.

Q: 3. Is the length from the Y ? I am looking to put two mics on a single incoming line, 6 feet apart. Will this work?

A: The Kopul XLR Y Cable (XLR-M to Dual XLR-F) is 15" long overall. The manufacturer has not provided a distinction for length either before or after the split, but the Y-junction is approximately halfway down the cable's length.

Q: 4. I'd like to connect the line output (3.5mm mini-jack) on my Zoom H5 recorder or my Shure VP83F compact shotgun mic to the XLR input on a Blackmagic Ursa Mini. Is this the correct cable to do so?

A: Yes

Q: 5. Can this be used with a dual wireless receiver like the Sennheiser XSW dual wireless system?

A: The Kopul XLR Y Cable (XLR-M to Dual XLR-F) could be used with a pair of wireless receivers, although all audio will be mixed to mono via the single XLR output connector.

Q: 6. How is this cable wired? Is it balanced? I'm looking for T-2, R-3, S-1...

A: The Kopul Stereo Right-Angle 1/8" Male Mini-Jack to XLR Male Cable (1') is balanced as it has 3 conductors.

Q: 7. Can I use this Hosa Technology Pro REAN XLR Female to 1/4 TS Hi-Z Microphone Cable to the out put of the Behringer MIC100 preamp and connect it to my guitar amp (with 1/4 TS unbalanced input connector)?

A: This cable will allow you to connect the output of a mic preamp to your guitar amp. This application however is not generally recommended mostly due to the guitar amps being midrange heavy which causes feedback issues with microphones, also the preamp outputs a line level signal which is hotter than the instrument level signal most guitar amps are designed for.

Q: 8. Will this work with a Rodelink Wireless system?

A: Absolutely! Works like a charm. Just remember it won't screw down into the mic Reciever unit, so pick a safe spot in your bag/rig to avoid straining the cable.

Q: 9. Would I be able to use a XLR-TO-USB SIGNAL ADAPTER with this mic to record directly into my laptop? Thinking a Blue Microphones Icicle XLR to USB Mic Converter/Mic Preamp or a SHURE X2U XLR-TO-USB SIGNAL ADAPTER would work for this?

A: Either of these adapters will work, however, the Icicle has been discontinued, and the Shure is much better quality.

Q: 10. Neutrik NC4MX-B 4-Pin XLR Male Connector will these fit canon xa20

A: If you're looking to plug a mic into the hot shoe inputs, you'll need a three pin version.