The Dalite 58 x 104" Ascender Electrol Motorized Front Projection Screen is an interesting and functional option for venues where a ceiling mounted screen is not viable.

This unique screen can be recessed into the floor and with the flip of a switch rise to comfortable viewing height. If you prefer not to recess the screen into the floor, the Ascender can be mounted within an attractive case. The concealed approach to this screen makes it appealing to people who are limited by space and need a screen which can be hidden when not required. 

220 Volts, 50Hz    Floor Mounted    Tensioned    119" Diagonal    HDTV Format    16:9 Aspect Ratio    Matte White Finish

Allows screen to be recessed into the floor for a concealed appearance or installed into a decorative surrounding

Motorized spring-assisted scissor mechanism raises the screen surface from the housing to ensure smooth operation

A trap door housing keeps the screen and lift mechanism hidden until the screen is activated

UL listed

Related Questions and Answers

Q: 1. Can these be used as continuous light as well?

A: The Dlite has a modeling light but it would not be a recommended use of it to be used for video.

Q: 2. Can I use the new EL Skyport transmitter to trigger my older Elinchrom Dlite 4 it strobes and use two newer and two older flashes altogether?

A: All will trigger, but remote power control will not be possible with the older units.

Q: 3. Will it take a 9mm shaft? (Hate to be picky.)

A: The Manfrotto 026 Lite-Tite Swivel Umbrella Adapter will only accept an umbrella shaft up to 8mm.

Q: 4. Hi. What is the GN for this strobe? I am looking to get a few for studio assignments which requires F8-F13 apertures.? I have a phottix Luna beauty dish i wish to mount on this strobe, is there a mount converter for it? what is the syn cable supplied: 3.5mm - PC? I'm using a pentax K3 so will have to sync using cable with RF603CII, will it work? Thanks in advance.

A: I don't remember the GN off hand, but it will most definitely handle the apertures you are mentioning. It's very powerful! You can get conversion mounts for it either at b&h or most definitely amazon. the sync cable supplied is what you also mentioned. but I'm not sure about the rf603cII. I use radio remote triggers (pocket wizards)

Q: 5. Can I use this light kit with Leica M10for studio shootings?

A: Yes you could use this with a Leica M10.

Q: 6. Hi , can i use it with Leica q ?

A: While you can use this kit with the Leica Q, it has not been tested to our knowledge. Your results may vary.

Q: 7. Is the honeycomb grid and hood diffuser included in this set? If not, do you have anything that will work with this set?

A: A softbox is included for each head in this kit. However, there are no grids available to fit them. For grids to fit the lamp heads using a reflector, you may consider the Elinchrom Reflector and Honeycomb Grid Set, B&H # ELCGS8.25 . https://bhpho.to/36ARezX

Q: 8. does this work with the Vello Captain Freewave?

A: The internal receiver does not work with the Vello FreeWave Captain. If you use a receiver on the light then you will be able to use the Vello FreeWave Captain.

Q: 9. Can you tell me which softbox is compatible with Elinchrom D-Lite 400W/s RX 4 Flash Head?

A: You may use a softbox such as the Elinchrom Rotalux Deep Octabox (100cm / 39"), BH # EL26648 along with a speed ring to attach it such as the Elinchrom Rotalux Speed Ring for Elinchrom Flash Heads, BH # EL26570. https://bhpho.to/3XZVRNP https://bhpho.to/3XzSKwp

Q: 10. I had previously ordered this and it came with an EL-Skyport Speed Transmitter. Does it still include this remote trigger?

A: Unfortunately, a transmitter is not included with the Elinchrom D-Lite RX One Flash Head. A compatible option is the Elinchrom EL-Skyport Transmitter Plus, BH # ELSTP. https://bhpho.to/3c95qbf