The Avenview DVI-PROWALL-4X 4-Display Video Wall Processor is designed to expand one video input to 4 displays in different layouts in real time. Real time processing is made possible through digital transmission processing chips for displaying content on your flat panel displays or projectors.

Bundled with its own control software, the user can simply configure different layouts such as 1x1, 1x3, 1x4, 2x2, and mosaic. The DVI-PROWALL-4X can accept both DVI and HDMI sources, and the embedded scaler converts signals from the DVI or HDMI source to match the native resolution of the monitors, flat panel displays, and projectors connected to the 4 outputs connectors. The output resolution can be selected for each display up to PC resolutions WUXGA (1920x1200).

The DVI-PROWALL-4X sends the input source video through the DVI/HDMI interface to the connected displays based on the physical layout and configured in the software. Recommended applications for the DVI-PROWALL-4X include retail digital signage, commercial applications and broadcasting, education, and surveillance systems.

Four DVI/HDMI outputs from 640x480 to 1920x1200

Supports HDMI/DVI input from 640x480 to 1920x1200

Supports video resolution up to Full HD 1080p

Supports PC resolution up to WUXGA

HDCP compliant

Image parameters and layouts saved in computers can be loaded for later use

Firmware upgradable for new features and technology enhancements

Supports IR remote control

Supports input rotation

Software control through USB and Ethernet

Resize, position, zoom output video

User-selectable output settings, up to 1920x1200

Each DVI/HDMI output has an independent controllable display area

Supports remote control to switch 1x1, 2x2, 1x3 rotate, and 1x4 rotate mode

Each output can support OSD control for edge correction

Related Questions and Answers

Q: 1. How to present 4 different ppt slides in a 4 monitor video wall?

A: This switcher can be configured in a few different ways. In picture-in-picture mode this switcher will allow you to have 4 different signals on 4 different monitors. So you could connect 4 computers, assign each to a screen and display 4 different PowerPoint slides that way. You can also set this as a 2x2 Video Wall. That means you would have a signal from one source spread out over the 4 screens. PowerPoint will not allow you to show 4 slides at a time, so you would need to create a custom slide or image that has 4 slides on it and make sure you have it appropriately sized and positioned on the screen.

Q: 2. will this get my laptop (VGA) directly into my TV (HDMI)?

A: You cannot go from a standard analogue (VGA) output to a digital (HDMI) output without a digital adapter. It works well going from digital (HDMI) output to an analogue (VGA) output.

Q: 3. Does this support Atmos?

A: Yes, the Avenview 1x4 HDMI True 4K60 Splitter with EDID supports Dolby Atmos.

Q: 4. Can this be used with an Apple Lightning to HDMI converter for iPad Air?

A: Yes, without any issues.

Q: 5. I want to convert a HDMI out put from a Livestream hd 550 to a Ethernet input of a mushroom networks streamer, will this work?

A: the HDM-C6IP-SET is intended to work as a SET (Sender and Receiver). It depends on the Mushroom Network Streamer if it is able to decode the signal from the Sender connected to your Livestream HD 550.

Q: 6. Does this pass HDMI CEC commands from the input to all outputs?

A: Not that we are aware of. It is not listed as supported in the spec sheet or in the user manual.

Q: 7. fit mac?

A: This cable will work on any Mac with an HDMI port.

Q: 8. Does 4X powermate, 2 , fits in to SCT rear cell adopter(2 ) or directly in to SCT rear cell(I have 8 SCT). In other words how do I hook up this 2 powermate to rear of 8 SCT.Second Question: I have a cannon DSLR with T ring and 2 adopter. Does this works with this?.

A: 1) The bare end of the 4x Powermate barrel does slide into the 2 adapter that screws onto the SCT rear cell.You'll need to make sure the 4x Powermate is firmly secured into the 2 adapter since the 4x Powemate is a bit heavy (especially with the camera attached!).2) No, the camera cannot be attached to the 4x Powermate by simply using a 2 adapter and Canon T-Ring.To place an SLR camera onto the 4x Powermate (unfortunately) another adapter is necessary, which is the TeleVue 4x Powermate T-Ring.The 4x Powermate has to be partially disassembled then the Televue 4x Powermate T-Ring gets screwed onto the 4x Powermate. Then, the Canon T-Ring is screwed onto the 4x Powermate T-Ring. Then the camera can be attached to the Canon T-Ring.

Q: 9. Does it work with 220v AC power?

A: The unit will accept multi-voltage.

Q: 10. To use this objective in Fujifilm XT4 ¿Do you have de adapters?

A: Unfortunately, we do not have an adapter to use the Konus 4x Achromatic Objective (Silver) on a Fuji XT4.