The brass Furniture Feed Cover for 6" SmartFit Poke-Thru from FSR has two cable-egress openings for use with the 6" Poke-Thru floor box. The entire cover door swings open 180°, and the two smaller cable access doors fold down for cable egress while the cover door is secure. The brass brushed-aluminum architectural finish of the cover matches your Poke-Thru.

Made in the USA

Related Questions and Answers

Q: 1. Are these for 1 tube scope? Will these fit a Marlin Model 60 dovetailed receiver? Is this a set of 2?

A: Yes they Fit a 1 In tube,they fit the Dovetail groove on top of my Remington Receiver on my 22 Pump,Not sure of Design of receiver on your Marlin 60 and Yes they are a set of 2, hope that helps,I like the Fact I can use my Iron Sights without removing the Scope.

Q: 2. I've looked and looked...what are the 3 heights that this can rise to?

A: The heights are, 1 5/8" (no leg extensions),3 1/8" (1 leg extension),4 5/8" (2 leg extensions).

Q: 3. What's the height of this computer stand?

A: Dimensions 2 x 24 x 11.8" / 50 x 610 x 300 mm

Q: 4. How deep of equipment can this box support?

A: The FSR CB-224S Series 4RU Ceiling Box with Pole Mount Adapter & Smart Power Module (BH # FSCB224SP) is 12" high. There is1-3/8" clear space on both sides of rack cage when inside the box, to allow for wire bundles. The interior cage is 4 RU. The useable rack unit (RU) depth is 14.27 inches.

Q: 5. does this come with the rack rails and what shelves come with it ?

A: The Gator Frameworks Elite Series Furniture Sidecar Rack Cabinet comes without rack rails or shelves, which are optional and available separately.

Q: 6. There are two sides of adhesive - does it stick to the mat and mat board?

A: You apply these strips to a backing board with their adhesive tape -- for your purposes the adhesive tape is 1-sided, being already attached to the firm plastic strip.The adhesive doesn't cover the full width of the plastic strip; it leaves perhaps 1/5 of plastic free to act as a trap for the item being mounted. There is no adhesive in direct contact with the mounted item's surface.This is ideal for use on a backing board where glass and/or matting will keep the artwork from falling out of the strip's thin rim of plastic. It wouldn't work for a large paper item which lacked a glass in front -- the paper's weight would pull it out of plastic edges, I suspect. The role of this is to prevent artwork from shifting around after it matted and framed.Note that the adhesive holding the mounting strip is outside the dimensions of the artwork: the backing board needs to be around an inch wider than the artwork to have room for the strips.

Q: 7. Will this fit on a Leica M4-P hotshoe? The Leica M4-P has a pin at the end of the hotshoe.

A: No, Leica only lists the new Q3 as compatible with the Leica Hot Shoe Cover (Brass, Blasted Finish).

Q: 8. Is this connector Size D?

A: Yes, it fits a standard, D size panel cutout, same as an XLR connector.

Q: 9. Wow, so what is is made out of? Seems to me a plastic polycarbonate job. Not even MDF.

A: Per Kensington: These are made of hard plastic material.

Q: 10. I will be installing this item in a wood floor, can the wood be attached to the cover?If so, howI will I access the outlet?

A: This box is designed for use with carpeting. Please contact FSR directly for help with hardwood flooring:FSR:Tel: 800-332-3771Website: a href= http://www.fsrinc.com/ target= _blank http://www.fsrinc.com//a