The black E6 Directional Earset Mic, Medium Gain, with Detachable 1mm Cable and Screw-On TA4F Connector for Sabine Wireless Transmitters from Countryman is a vocal microphone with an adjustable boom that weighs less than one-tenth ounce. It can be used on either ear for capturing audio and rejecting unwanted sound, feedback, or surrounding noise from stage monitors or nearby speakers in houses of worship, theater, and outdoor vocal and speech applications.

The low-profile, directional E6 Earset virtually disappears against the skin, so performers forget they're wearing a mic. Three sensitivity options cover general speaking to extremely powerful vocals and four color options allow you to match the E6 to your skin tone for minimum visibility.

In addition, the E6 Earset features a pattern-changeable directional microphone for maximum isolation and gain before feedback, but is available as a water- and wind-resistant omnidirectional microphone too. This directional E6 Earset's cable terminates to a screw-on TA4F connector for direct connection to a Sabine SW16TX, SW30TX, SW1600, SW3000, or ST50T wireless bodypack transmitter.

For Vocals and General Speaking    Detachable 1mm Cable    Screw-On TA4F (SS), See Description    30 Hz to 15 kHz Frequency Response    Includes Cardioid & Hypercardioid Caps    Headroom for Strong Vocals    Windscreen    Cable Clips    Carrying Case

The Countryman E6 head-worn Earset is small and lightweight, and is hardly visible from a distance.

The E6 Earset's stainless steel boom is built tough and can be bent and re-bent many times to fit different performers. The E6 is highly resistant to makeup, sweat, and moisture when used with the supplied protective caps.

The flexible boom is easily shaped right on the performer's face and is available in multiple skin tones. Their protective caps let you shape the frequency response for different situations or to match other microphones; caps for the directional earset adjust the pattern from cardioid to hypercardioid. Choose a sensitivity for speaking or singing with up to 145 dB SPL capability.

The E6 provides high-quality audio with low distortion and an SPL of up to 145 dB. It delivers rich, full band audio quality.

Easy adjustment keeps the mic in a position for rejecting unwanted sounds. Countryman's omnidirectional Earset offers a reduction of 12 dB compared to a lavalier mic, while the directional E6 Earset provides even more isolation. Excellent for houses of worship, theater, and outdoor events.

An E6 replacement cable installs in seconds. The snap-on cables are rugged and available for almost any wireless transmitter or for XLR inputs with phantom power.

For speaking and vocals.

Related Questions and Answers

Q: 1. Will the Kirk L bracket for the Canon 6D Mark II work with this ball head?

A: Yes it will. The Kirk L-Bracket for Canon 6D Mark II has an Arca-Type Compatible Dovetail Mount, B&H # KIBL6DII. This head is Arca-Type Compatible. https://bhpho.to/2HoxzIY

Q: 2. what is the difference between GH1382QD?

A: The Gitzo GH1382TQD Series 1 Traveler Center Ball Head with Arca-Type Screw Knob QR Receiver weighs about 20% less than the GH1382QD ball head and has a slightly lower load capacity.

Q: 3. I have a Peak Design arcs-Swiss type plate would this head fit it?

A: I have one square Peak Design plate with a screw in the middle of the plate. It does not fit my Gitzo 1385TQD because the screw has 14mm diameter and it touches the safety pin. Solution (if you want to keep the safety pin): use a different screw with a small head similar to the B107 Screw (1/4"-20 Thread) that locks with M2.5 Hex Key. Another solution is to find a screw with a low profile head. By the way, the JOBY Ballhead X plate and JOBY QR Plate 5K can be used thanks to low profile screw head.

Q: 4. Would a Canon 5d Markiii fit on this?

A: Yes, this one will fit any full frame DSLR, but it depends on a lens you are going to use. I use it with Nikon D700 or D800 and Nikon 70-200mm VRII as a maximum. This body/lens combo weighs around 2.5 kg (PG-01 load capacity is 3.6 kg/8 lb), but you should be careful how far from the tripod centre you will push them on a nodal slide. Although, primary target is a mirrorless camera user, I like how sturdy, but light and small PG-01 is, as well as its price in comparison to PG-02. I use quite long nodal slide with it (RRS MPR-192), as for example, the entrance pupil for mentioned lens (no parallax point) at 200mm is behind the camera flange and you need to have that lenght of a slide to push everything forward to the far end. I hope this can help.

Q: 5. I am wondering if RSS L Plate for a9, a7rIII or 5D IV will fit this Gitzo GH1382TQD? I am hearing that the Gitzo has safety pin which takes only Gitzo specific lates?

A: All B&H customers using this head report it accepts Arca-Swiss plates without issue.

Q: 6. This Gitzo travel ball head is too sticky and not smooth like my old Promaster cheapo ball head. Is there anyone else with this issue?

A: This head is very good and should not at all be sticky. Check the knobs and see if different tightening positions make the difference.

Q: 7. I have a Spider plate attached to my Nikon D750 (for Spider belt). Can I use this plate together with the Spider plate? If not, what's my better option, please?

A: Yes, you can attach the Spider clip to the bottom of the RRS plate, as it has 1/4-20" threading.

Q: 8. Does this have the Quick Detach socket built into the plate?

A: The L85 includes two QD sockets.

Q: 9. Would this be suitable for real estate panoramas?

A: Most definitely.

Q: 10. Will this fit a Canon EF 70-200 f/2.8L IS III Lens?

A: Yes this plate is compatible with Canon EF 70-200 f/2.8L IS III Lens.