The Countryman E6i Cardioid Microphone is a miniature ear-set microphone for virtually invisible operation in stage performances, trade shows, houses-of-worship, auctions, lectures and much more.

The cardioid version effectively minimizes off-axis feedback and noise from nearby monitor speakers, instruments and noisy sources. Flexible microphone positioning is maintained and the included windscreen minimizes the wind noise often associated with cardioid microphones.

The E6i is set apart from the original E6 with its softer flexible boom and silicon ear-pads. The flexible boom provides ease of boom adjustability to accommodate multi-user applications.

A wide variety of colors and connections are available for use with various wireless transmitters. This version is beige and features a 1/8" Locking-mini connector for use with Sennheiser wireless transmitters.

1/8" Locking-mini for Sennheiser    1mm Diameter Cable    Headroom for General Speaking    Cardioid    Beige

A miniature cardioid capsule is mounted to a low-profile, flexible frame. This lightweight, unobtrusive design is available in various colors that virtually render the entire microphone invisible against the skin.

The included removable, quick-swap cable detaches from the actual headset, making it completely replaceable in the event of a short or break. The replaceable cable design makes upgrading wireless microphone systems easy, as they are available in a wide selection of connections to accommodate various wireless transmitters.

The cardioid polar pattern is effective in minimizing off-axis residual noise from e nearby monitor speakers, instruments and loud sources. The result is increased signal-to-noise ratio and minimal feedback. The flexible boom provides a custom fit for multiple users and close microphone positioning. The E6i is also available in an omnidirectional version for maximum control over wind noise and plosives (popping).

This E6i's sensitivity response is optimized to accurately capture general speech without noise and distortion.

Related Questions and Answers

Q: 1. Will this remote work with my Nikon D810?

A: Yes, the Nikon WR-R11a/WR-T10 Remote Controller Set is listed as compatible with the Nikon D810.

Q: 2. Will this remote work with d850?

A: No, the WR-R11b/WR-T10 combo will not work with the Nikon D850 camera. It uses the 10-pin Nikon connection. The WR remote set you need is this one, the WR-R11a/WR-T10 set: https://bhpho.to/3a4nmme

Q: 3. Will this work with a Nikon 780

A: Yes Nikon WR-R11b/WR-T10 Remote Controller Set is compatible with the Nikon D780.

Q: 4. Can this unit work with my D850 set to Back Button Focus

A: Yes, you can assign AF-ON through the Nikon D850 DSLR camera Setup Menu for the Fn button on the Nikon WR-T10 Wireless Remote Controller Transmitter.

Q: 5. RE: WR-R11b receiver. Is there an indicator light that confirms the unit was activated?

A: Yes, the WR-R11b has two LED indicator lights that signify an established connection as well as triggering. The top LED flashes red during triggering and/or AF activation and the bottom light flashes a longer green pulse when a photograph is fired (as opposed to a continuous short green pulse every few seconds that signifies the unit is connected to the WR-T10).

Q: 6. Does this work with Elinchrom Five ?

A: Yes, the Elinchrom Deflector Set for Softlite Reflectors and Rotolux Softboxes is compatible with the Elinchrom FIVE Monolight Kit.

Q: 7. Does this reflector set work well with umbrella shaft position of Profoto B1,B2, D1?

A: While this set has not been tested with Profoto heads, it should fit as Profoto heads like the B1, B2, and D1 can accept both 7mm and 8mm umbrella shafts.

Q: 8. Is the new Nikon WR-R11b/WR-T10 Remote Controller Set compatible with the D850. If so how is it different than the the WR-10 remote controller set?

A: Yes, you have to chose the one that has the 10 pin connector. This set has more range and is also compatible with the newer cameras.

Q: 9. is there a way to stop the red blinnking warning light when not using for flash, i.e. remote trigger?

A: There is no way to deactivate the red LED light on the Nikon WR-R11a/WR-T10 Remote Controller Set, but you could cover it with a small piecr of black gaffer's tape, if it is annoying.

Q: 10. Does this work with an Elinchrom Snaplux 24 in octabank and an elb 500 head ? Thanks.

A: No it doesn't