The 120V 24746LS Tensioned Contour Electrol 65 x 104" Motorized Screen from Da-Lite supports ceiling or wall mounting. Tensioned screens ensure the smoothest surface possible.

123" Diagonal / 16:10 Aspect Ratio    HD Progressive 1.3 Surface    1.3 Gain / 150° Viewing Angle    Smooth Roll Technology    Tensioning Cable System    White Housing Finish    Silent Motor    Low Voltage Control (LVC)

Ideal for applications where projector brightness and screen size require an increase in gain, the white surface offers high-fidelity color reproduction, and allows for more flexibility with ambient light conditions. This surface works for video as well as charts and graphs in a corporate setting. Cone 150° Gain: 1.3

• Standard Low Voltage Control (LVC) to keep your screen operation flexible
• Smooth Roll Technology to keep your screen flat
• Slim-Tab, a lower profile, stronger tab design to keep your screen taut
• Tensioning Cable System to prevent warping and ensure even lateral tension
• Seamless screen surface

The housing for this screen features a white finish

Designed to provide silent operation when raising or lowering the screen.

Allows the included wall switch, as well as devices such as automation systems, third-party wall switches, and remotes that support LVC, to raise or lower the screen remotely.

Related Questions and Answers

Q: 1. Hi!Does this model: Impact 2 Section Articulated Arm with Camera Bracket can support a DSLR camera (EOS 60D) with a ring light & the Zoom H4N (those 2 mounted on my camera) ?If not, what kit would ?Thank you very much !

A: I don't think so. I used these mounts for a tiny Marshall video camera. (Smaller than a GoPro) it worked well for that, but I can't imagine it would support a 60d. Especially with accessories. I'd look for something that is 100% metal construction if I were supporting a heavier and more expensive camera rig.

Q: 2. Can I directly mount this on my tripod (with 3/8" male screw) to bottom stud and still attach the camera bracket at the other end?

A: Yes, you can mount this arm to a 3/8" male thread as one end of the arm has a 3/8" female thread.

Q: 3. I’m considering this device to mount some PTZOptics cameras to a lighting truss. However it looks as though the knobs on the camera bracket extend above the surface of the camera bracket in such a way that they would impact the bottom of the camera and prevent mounting. Is this an illusion or would it be a problem?

A: The knob does extend past the level of the plate. Depending on the size of the camera base you might have an issue. The other thing to consider is these are only rated to 3.3lbs.

Q: 4. What is the weight capacity when the arms are at maximum length horizontally?

A: The, Impact 2 Section Double Articulated Arm with Camera Bracket at full extension can support up to 11 lbs.

Q: 5. How would this compare to the equivalent manfrotto one as far as stability and durability?

A: Impact can take more payload and weighs less than the same Manfrotto version, however it could be said that the Manfrotto is built better or works smoother, your mileage may vary with that however. Stability/payload wise it seems Impact is the way to go.

Q: 6. What's the diameter of the len hood?

A: The Nikon HB-104 Lens Hood's diameter is slightly under 6.5”.

Q: 7. Can you purchase longer arms?

A: The longest articulating arms we carry would be the 33-inch 3-section articulated arm options listed below; the Impact 3 Section Articulated Arm without Bracket, B&H # IMBHE118, Manfrotto 196AB-3 Articulated Arm - 3 Sections, No Bracket, B&H # MA196AB3, Impact 3 Section Double Articulated Arm without Bracket, B&H # IMBHE119, or the Manfrotto Double Articulated Arm - 3 Sections Without Camera Bracket, B&H # MA396AB3. The next longest options would be the 24-inch 2-section articulated arm options, such as either the Impact 2 Section Double Articulated Arm without Camera Bracket, B&H # IMBHE117, or the Manfrotto Double Articulated Arm - 2 Sections Without Camera Bracket, B&H # MA396AB2. These are the options that would be longer than the 23-inch arm listed above.

Q: 8. Hi!I have a Zoom H4N. I want to use it for the audio of my Youtube videos of me talking to the camera (never thought I would write something like that in my life...!)To do this, I need your help because I'm a total newbie at this ! So 2 questions :1) What king of connection cord do I need to connect my zoom machine with my DSLR (EOS 60D) ?2) I need a mic that let me be at a distance form my camera while I'm shooting. The same as the one tv announcers clipped to their jacket or blouse on the news. What kind do you suggest me under 150$Thank you so so much for your precious help :)

A: Q1 - I do not have an Zoom H4n but it appears a 3.5mm audio cable will work. Like this one: Sescom LN2MIC-ZOOMH4N - Line to Microphone Attenuation Cable for HDSLR Cameras.Q2 - Any lavalier (ex Polsen, countrymen) mic should work you can purchase them from about $23 and up

Q: 9. Can this be attached safely to a C-stand?

A: Yes this can be attached safely to a C-stand that has a grip arm already attached to it.

Q: 10. what would i need to use this with a shock mount ?

A: Please contact live chat as we need more detailed info.