The Countryman E6i Cardioid Microphone is a miniature earset microphone for virtually invisible operation in stage performances, trade shows, houses-of-worship, auctions, lectures and much more.

The cardioid version effectively minimizes off-axis feedback and noise from nearby monitor speakers, instruments and noisy sources. Flexible microphone positioning is maintained and the included windscreen minimizes the wind noise often associated with cardioid microphones.

The E6i is set apart from the original E6 with its softer flexible boom and silicon ear-pads. The flexible boom provides ease of boom adjustability to accommodate multi-user applications.

A wide variety of colors and connections are available for use with various wireless transmitters. This version is beige and features a 4-pin Hirose connector for use with specific* Audio-Technica wireless transmitters.

4-pin Hirose for Audio-Technica    1mm Diameter Cable    Speaking & Vocals    Cardioid    Beige

A miniature cardioid capsule is mounted to a low-profile, flexible frame. This lightweight, unobtrusive design is available in various colors that virtually render the entire microphone invisible against the skin.

The included removable, quick-swap cable detaches from the actual headset, making it completely replaceable in the event of a short or break. The replaceable cable design makes upgrading wireless microphone systems easy, as they are available in a wide selection of connections to accommodate various wireless transmitters.

The cardioid polar pattern is effective in minimizing off-axis residual noise from e nearby monitor speakers, instruments and loud sources. The result is increased signal-to-noise ratio and minimal feedback. The flexible boom provides a custom fit for multiple users and close microphone positioning. The E6i is also available in an omnidirectional version for maximum control over wind noise and plosives (popping).

This E6i sensitivity response is optimized to accurately capture speaking and vocals without noise and distortion.

Related Questions and Answers

Q: 1. How do you remove this head if mounted on a tripod, so you can use fluid head on a monopod or other device?

A: If you are ordering this product (just the head), there is no need to remove it from anything as it is the head only. If the FM18 head is mounted to a tripod raise the center post and lock it. Look underneath the center post top cap and you will see two allen screws. Loosen these screws and the head will now twist off.

Q: 2. Can I use a pocket wizard? Does the flash head have a sync port? If so, what kind (2.5mm, 3.5mm or pc sync)?

A: No. The unit offers no sync ports. The following unit offers a built-In radio and bluetooth release system.

Q: 3. Does this head is compatible to Manfrotto Xpro Section Monopod?

A: Yes it is. You can use this head with the Manfrotto XPRO Prime Base 3-Section Aluminum Monopod, BH #MAMMXPROA3BU.

Q: 4. is the plate the same or compatible with Dji Ronin SC?

A: The plate form the SmallRig CH10 Compact Fluid Head is compatible with the DJI Ronin SC.

Q: 5. Is this arca compatible for "L" brackets?

A: Unfortunately the clamp is not arca compatible.

Q: 6. Does anyone use this with a canon 5D mark II? If so, how is it?

A: This should be just about right for the 5D Mark II and lens. That combination can be 4-8 lbs. and should be a sweet spot for the head. Reports are that it works well with much lighter cameras such as the Sony NEX 7 with success. Just be aware that while The S6 has adjustable counterbalance, tilt drag adjustment and pan/tilt locks, there is no pan drag adjustment. All in all however, you do get a lot of video head for the money.

Q: 7. What is the maximum vertical distance between the Arca plate surface and upward to the horizontal tilt/swing pivot point?

A: Maximum distance is approx.7.5 inches.

Q: 8. Will this work with the Nikon 400m f2.8. I am worried that I will not be able to attach to the foot of the lens, or do you have to attach the PL-100 plate to the lens foot?

A: You attach the plate (PL100) to the lens foot.

Q: 9. States that this is a 75mm bowl. But is it possible to remove the bowl so that it can be mounted on a flat mount tripod or slider?

A: Yes, this has a removable tie-down stud to convert to a flat base head.

Q: 10. Will this fit into a schatler v20 legs?

A: Yes, the Benro BV10H 100mm Video Head can be used with 100mm bowl tripods, like those paired with the Sachtler Video 20 S1 Fluid Head.