The Countryman E6i Cardioid Microphone is a miniature earset microphone for virtually invisible operation in stage performances, trade shows, houses-of-worship, auctions, lectures and much more.

The cardioid version effectively minimizes off-axis feedback and noise from nearby monitor speakers, instruments and noisy sources. Flexible microphone positioning is maintained and the included windscreen minimizes the wind noise often associated with cardioid microphones.

The E6i is set apart from the original E6 with its softer flexible boom and silicon ear-pads. The flexible boom provides ease of boom adjustability to accommodate multi-user applications.

A wide variety of colors and connections are available for use with various wireless transmitters. This version is beige and features a 4-pin Push-lock connector for use with Lightspeed wireless transmitters.

4-pin Push-lock for Lightspeed    1mm Diameter Cable    Speaking & Vocals    Cardioid    Beige

A miniature cardioid capsule is mounted to a low-profile, flexible frame. This lightweight, unobtrusive design is available in various colors that virtually render the entire microphone invisible against the skin.

The included removable, quick-swap cable detaches from the actual headset, making it completely replaceable in the event of a short or break. The replaceable cable design makes upgrading wireless microphone systems easy, as they are available in a wide selection of connections to accommodate various wireless transmitters.

The cardioid polar pattern is effective in minimizing off-axis residual noise from e nearby monitor speakers, instruments and loud sources. The result is increased signal-to-noise ratio and minimal feedback. The flexible boom provides a custom fit for multiple users and close microphone positioning. The E6i is also available in an omnidirectional version for maximum control over wind noise and plosives (popping).

This E6i sensitivity response is optimized to accurately capture speaking and vocals without noise and distortion.

Related Questions and Answers

Q: 1. Does this head is compatible to Manfrotto Xpro Section Monopod?

A: Yes it is. You can use this head with the Manfrotto XPRO Prime Base 3-Section Aluminum Monopod, BH #MAMMXPROA3BU.

Q: 2. Does this head actually come with a quick release plate or do you have to buy the Induro plate separately?

A: Yes, the quick release plate is included.

Q: 3. Would the peak design base plate on my camera fit this clamp?

A: The FLM 55GX Centerball Tripod Head with SRB-60 QR Clamp takes Arca-Type compatible plates. So yes, a Peak Design Quick Release plate such as the Peak Design PL-S-3 Standard Plate will work.

Q: 4. is the plate the same or compatible with Dji Ronin SC?

A: The plate form the SmallRig CH10 Compact Fluid Head is compatible with the DJI Ronin SC.

Q: 5. Can the panhandle be used on the left side?

A: Negative. The panhandle is molded into the right side.

Q: 6. Is able to support a compact konova k1 slider 48 cm?Or benro s4 head is better option?

A: Both the Befree Live Video Head and the Benro S4 Video Head (B&H #BES4) have an 8.8 pound load capacity. If you can keep the overall load below that mark you should be able to use either head. However you may find the Benro S6, B&H #BES6, a better option because it has a 13.2 pound load capacity.

Q: 7. Can I use a pocket wizard? Does the flash head have a sync port? If so, what kind (2.5mm, 3.5mm or pc sync)?

A: No. The unit offers no sync ports. The following unit offers a built-In radio and bluetooth release system.

Q: 8. Can i put it on a Manfrotto 562B-1 Monopod?

A: Yes, you can remove the plate that is on the Manfrotto 562B-1 Monopod and mount this S4 instead.

Q: 9. is the plate compatible with Manfrotto 577 Rapid Connect Adapter?

A: Yes. All Benro S Series and BV series heads are compatible with the Manfrotto 501PL and 504PLONG plates.

Q: 10. Can this head fit onto a Sirui T-024sk?

A: Yes. That is correct! You would be able to mount This item BH #BES2 on the SuruiT-024SK Compact Tripod