The 120V 34465L Cosmopolitan Electrol 69 x 110" Motorized Screen from Da-Lite is a ceiling or wall mounted electric screen. A variety of finishes and veneer options are available.

130" Diagonal / 16:10 Aspect Ratio    High Contrast Matte White Surface    1.1 Gain / 100° Viewing Angle    Low Voltage Control (LVC)    Includes 3-Button Wall Switch

High Contrast Matte White is a fiberglass surface with a gray base for deeper reproductions of black, which improves contrast. It is for non-high-definition projection and environments with moderate ambient light. Cone: 100° Gain: 1.1

Allows the included wall switch, as well as devices such as automation systems, third-party wall switches, and remotes that support LVC, to raise or lower the screen remotely

• Decora-style, three-position wall switch
• Standard black backing retains projected brightness
• Standard white powder-coated finish; available in black or veneer upon request

Related Questions and Answers

Q: 1. Will this adapt to lumix 45-175 or leica dg 25mm f1.4

A: The smallest adapter ring included with the Bolt VM-110 LED Macro Ring Light is 49mm, while both lenses you list above use 46mm filters/filter threads. As such, you would need a step-up ring, such as the Sensei 46-49mm Step-Up Ring, B&H # SESUR4649, to connect the ring light to your lens.

Q: 2. At maximum illumination and room temperature, how long can this provide continuous illumination for?

A: The manufacture does not list the maximum power used to run it. It runs on four AA batteries.

Q: 3. I assume this ring light would work with my Panasonic FV200?? Either with the regular 58mm filter thread or my 58-62 step-up filter ring that I use frequently?

A: It will not fit on the lens of the Panasonic Lumix FZ200, http://bhpho.to/18UmIPx. The ring flash with the 52mm adapter will not screw on because the lens moves in and out.The lens/camera can get damagedwith the ring flash on the lens when it is zoomed wide and closes.

Q: 4. Will this work on the Sony Nex 5 camera, since it don't have hot shoe to mount the control unit?Thank.

A: The VM110 Ring Light will work with almost any camera. Just set the unit for continuous illumination, position your lens in the middle of the Ring Light opening, and shoot in auto-exposure mode. The hot shoe mount is for mechanical support of the power pack only, and the lens mounts provided cover most DSLR lens threads, but are not necessary if you shoot through the Ring Light. You can also tilt the camera slightly and shoot off-axis to reduce the flat effect of ring lighting. I have used the VM110 successfully with a Canon point and shoot camera and an iPhone 5s.

Q: 5. will this fit a sony slt-A57

A: The Bolt VM-110 will be fully compatible with a Sony Alpha camera body with the use of the Sony Auto-Lock Shoe Adapter: http://bhpho.to/1gjWYR5

Q: 6. Is the bolt compatible with a canon power shot g15?

A: Yes with Canon FA-DC58D Filter Adapter for PowerShot G15

Q: 7. will the vm 110 work with Oympus OMd e m5 and the Pen series cameras?

A: This is not a speedlight, it just the lught source, the flash is of the same power as the light, it just preserves battery power, I'am sure it will work with the control unit in or off camera.

Q: 8. Could this be used with a Lensbaby Scout fisheye? Or a Lensbaby Composer?

A: The Lensbaby Scout fisheye does not have any filter threads plus it is too wide. There is nothing to attach the ring flash to and it will vignette on that lens. The Lens baby composer has a filter thread of 37mm so you can with a step up ring use the flash.The step up ring is, http://bhpho.to/1cvm3Ir*note the weight of the ring flash will be on the lens so it will be tough to keep the Lensbaby composer in position.

Q: 9. Will this work on a Nikon 1 J5 mirrorless camera (10-30mm)?

A: In the description it states that an adapter ring is included which threads onto the front of the camera's lens. If you camera lens can accept filters of one of the sizes entioned, then yes thus will work. Check the description of the Ring Light then check your camera!

Q: 10. Is this unit compatible with film cameras, especially Nikon F2 and F3, which lack a standard hot shoe? If not, can you recommend a ring light that is compatible with these cameras? Thanks.

A: To use that led light on those camera models you will need a bracket.This is one of many that will work.Custom Brackets CB Digital-SB Camera BracketB&H # CUCBDSB ? Mfr # CB DIGITAL SBhttp://bhpho.to/QXd09Q