The Countryman E6i Cardioid Microphone is a miniature ear-set microphone for virtually invisible operation in stage performances, trade shows, houses-of-worship, auctions, lectures and much more.

The cardioid version effectively minimizes off-axis feedback and noise from nearby monitor speakers, instruments and noisy sources. Flexible microphone positioning is maintained and the included windscreen minimizes the wind noise often associated with cardioid microphones.

The E6i is set apart from the original E6 with its softer flexible boom and silicon ear-pads. The flexible boom provides ease of boom adjustability to accommodate multi-user applications.

A wide variety of colors and connections are available for use with various wireless transmitters. This version is cocoa and features a 3-pin LEMO connector for use with Sennheiser wireless transmitters.

3-pin LEMO for Sennheiser    1mm Diameter Cable    Headroom for General Speaking    Cardioid    Cocoa

A miniature cardioid capsule is mounted to a low-profile, flexible frame. This lightweight, unobtrusive design is available in various colors that virtually render the entire microphone invisible against the skin.

The included removable, quick-swap cable detaches from the actual headset, making it completely replaceable in the event of a short or break. The replaceable cable design makes upgrading wireless microphone systems easy, as they are available in a wide selection of connections to accommodate various wireless transmitters.

The cardioid polar pattern is effective in minimizing off-axis residual noise from e nearby monitor speakers, instruments and loud sources. The result is increased signal-to-noise ratio and minimal feedback. The flexible boom provides a custom fit for multiple users and close microphone positioning. The E6i is also available in an omnidirectional version for maximum control over wind noise and plosives (popping).

This E6i's sensitivity response is optimized to accurately capture general speech without noise and distortion.

Related Questions and Answers

Q: 1. Is this compatible with a Tamron 100-600 lens?

A: Yes, the gimbal head and included quick release plate is compatible with the Tamron 150-600mm lens.

Q: 2. How do you remove this head if mounted on a tripod, so you can use fluid head on a monopod or other device?

A: If you are ordering this product (just the head), there is no need to remove it from anything as it is the head only. If the FM18 head is mounted to a tripod raise the center post and lock it. Look underneath the center post top cap and you will see two allen screws. Loosen these screws and the head will now twist off.

Q: 3. Will this gimbal head fit a slik pro 700 tripod?

A: Yes, it is compatible to the Pro 700.

Q: 4. Will it fit on my Sirui T-005BX?

A: Yes, the GH-M1 can fit onto the Sirui T-005BX.

Q: 5. When I mount a DSLR camera on the QR plate and slide it in place and try to tighten the plate locking handle, the handle runs into the camera body before it tightens all the way. How do I tighten the knob?

A: The knob is spring loaded. Simply pull the knob out and re position for another twist.

Q: 6. I would like an additional quick release plate for this head. What is recommended?

A: I would recommend either the Desmond DPC-140 Long Lens Quick Release Plate (140mm), B&H # DEDPC140, or the Oben QR-53 Long Lens Quick Release Plate (5.3"), B&H # OBQR53, for use with the Magnus GH-M1 Gimbal Head.

Q: 7. I intend to use this with a heavy long lens. Do you recommend?

A: The head is rated for up to 30lbs. So long as you balance the weight and use a tripod of adequate strength you will be fine.

Q: 8. Is this compatible with Benro GA269T Go Travel 2 Mg-Aluminum Tripod?

A: Yes, you should be able to remove the Ball Head on the GA269T and replace it with this Video Head.

Q: 9. What is the maximum vertical distance between the Arca plate surface and upward to the horizontal tilt/swing pivot point?

A: Maximum distance is approx.7.5 inches.

Q: 10. Has anyone tried the Really Right Stuff PG-CC Cradle Clamp for Gimbal Tripod Heads (BH #REPGCC) with this head?

A: To our knowledge the RRS PG-CC has only been tested with the Wimberley WH200 II, so the results may vary when using it with the Benro GH2.