The Countryman E6i Cardioid Microphone is a miniature earset microphone for virtually invisible operation in stage performances, trade shows, houses-of-worship, auctions, lectures and much more.

The cardioid version effectively minimizes off-axis feedback and noise from nearby monitor speakers, instruments and noisy sources. Flexible microphone positioning is maintained and the included windscreen minimizes the wind noise often associated with cardioid microphones.

The E6i is set apart from the original E6 with its softer flexible boom and silicon ear-pads. The flexible boom provides ease of boom adjustability to accommodate multi-user applications.

A wide variety of colors and connections are available for use with various wireless transmitters. This version is cocoa and features a 1/8" Locking-mini connector for use with Nady wireless transmitters.

1/8" Locking-mini for Nady    1mm Diameter Cable    Speaking & Vocals    Cardioid    Cocoa

A miniature cardioid capsule is mounted to a low-profile, flexible frame. This lightweight, unobtrusive design is available in various colors that virtually render the entire microphone invisible against the skin.

The included removable, quick-swap cable detaches from the actual headset, making it completely replaceable in the event of a short or break. The replaceable cable design makes upgrading wireless microphone systems easy, as they are available in a wide selection of connections to accommodate various wireless transmitters.

The cardioid polar pattern is effective in minimizing off-axis residual noise from e nearby monitor speakers, instruments and loud sources. The result is increased signal-to-noise ratio and minimal feedback. The flexible boom provides a custom fit for multiple users and close microphone positioning. The E6i is also available in an omnidirectional version for maximum control over wind noise and plosives (popping).

This E6i sensitivity response is optimized to accurately capture speaking and vocals without noise and distortion.

Related Questions and Answers

Q: 1. Will this still work if my camera weighs slightly under 4kg? Sometimes my rig weighs around 2.5 - 3.5kg

A: It will not. The load needs to be between 8.8 to 26.4 lb / 4 to 12 kg for the camera to properly balance. The only way you'd be able to use the head would be with it locked down, making it so you cannot pan and tilt for a shot.

Q: 2. Would this work on a manffrotto tripod?

A: Yes, as long as the Manfrotto tripod has a 1/4"-20 and/or 3/8"-16 screw, the Davis Sanford V9 Fluid Head is compatible.

Q: 3. Will this work with the base cold shoe mount of the mantis pod/pro?

A: No, The Mantis Pod is compatible with Arca Swiss plates. The PGYTECH SnapLock Plate Nano works with the following head. PGYTECH SnapLock Nano Swivel and Tilt Mount BH #PGSLNSTM https://bhpho.to/3WAUPXL

Q: 4. I just got my tripod with this head delivered. The tilt grag only turns about 3/4 turn from max drag to min. drag. When set to minimum drag, the head still bounces back up (with Nitrogen piston at minimum all--about 9 turns on that dial). Is something wrong with my head? Is there someway to get the drag fully loosened? I can't set the camera to not bounce back to level when I let go.

A: You have three adjustments. Two are for resistance which has nothing to do with stability of your camera. Resistance settings are only for resistance during a move. These are pan and tilt. When setting up the camera you should set these as loose as you can get them. Counter Clockwise is more resistance and Clockwise less resistance. The Nitrogen Piston setting is based on the weight of the camera. Again you need to set the Piston setting. Again clockwise tightens and counter clockwise loosens. Whe setting up the camera you need to be as clockwise as possible and then make sure that the camera plate and camera are balanced (not falling forward or backward). Once you have the camera balanced the turn the Nitrogen Piston Knob all the way counter clockwise and then back it off until your camera stablizes its position no mater what angle it is in. Then you can adjust the resistance to your preference. We have a rigging kit with follow focus and barn doors, so we had to add weight to the back of the rig for balancing. Normally you won't need to do this. If you have questions you can give us a call. 720-493-9966. Hope this helps. Bjarne Blume AVCOM Media Production

Q: 5. why is there a knob on the right and left side?

A: The knob on the right side top end of the Davis & Sanford V9 Fluid Video Head tightens the tripod plate into the head. Beneath that one still on the right, the bigger knob tightens or loosens the amount of Vertical tension on forward and backward motions. The knob on the left side tightens or loosens the panning capabilities, for horizontal motions of the fluid head.

Q: 6. How do I order another Quick release plate?

A: We are sorry to say that is not a part we sell. That is a Service Part which you'd need to obtain from the manufacturer directly. If you need assistance with that feel free to email us directly at askbh@bhphoto.com.

Q: 7. Can the quick release be rotated 90 degrees, so one can use this head with an L-bracket (plus lens with no tripod collar)?

A: The QR clamp does not rotate. A QR plate is included for mounting any camera to the head.

Q: 8. Will it fit the Peak Design travel tripod?

A: Not really suggest as a bushing would have to be set in place in order to mount system. The following is needed in order to do so. Oben 3/8"-16 to 1/4"-20 Reducer Bushing BH #OB1039 • MFR #OB-1039 https://bhpho.to/3FsBYah

Q: 9. What is the diameter of just the head cylinder, minus the knobs or plates?

A: it is 2.5 inches in diameter.

Q: 10. Will an Arca Swiss type plate attach to the top of this? I specifically chose this mode because it doesn't have the proprietary Manfrotto QR plates.

A: Yes. I bought a Hejnar 3.25 Arca type plate. It fits perfectly on top. I had to go to a hardware store to pick up nuts and bolts to secure it down. The thumb nut that comes with the Manfrotto will thread in, but will not prevent twisting since it mates with one thread. You need at least two nuts&bolts to prevent the Arca clamp from twisting on the head.