The Countryman E6i Cardioid Microphone is a miniature ear-set microphone for virtually invisible operation in stage performances, trade shows, houses-of-worship, auctions, lectures and much more.

The cardioid version effectively minimizes off-axis feedback and noise from nearby monitor speakers, instruments and noisy sources. Flexible microphone positioning is maintained and the included windscreen minimizes the wind noise often associated with cardioid microphones.

The E6i is set apart from the original E6 with its softer flexible boom and silicon ear-pads. The flexible boom provides ease of boom adjustability to accommodate multi-user applications.

A wide variety of colors and connections are available for use with various wireless transmitters. This version is tan and features a 6-pin Hirose connector for use with Samson wireless transmitters.

6-pin Hirose for Samson    2mm Diameter Duramax Cable    Strong Vocals    Cardioid    Tan

A miniature cardioid capsule is mounted to a low-profile, flexible frame. This lightweight, unobtrusive design is available in various colors that virtually render the entire microphone invisible against the skin.

The included removable, quick-swap cable detaches from the actual headset, making it completely replaceable in the event of a short or break. The replaceable cable design makes upgrading wireless microphone systems easy, as they are available in a wide selection of connections to accommodate various wireless transmitters. The Duramax 2mm diameter cable provides extra strength, flexibility and durability.

The cardioid polar pattern is effective in minimizing off-axis residual noise from e nearby monitor speakers, instruments and loud sources. The result is increased signal-to-noise ratio and minimal feedback. The flexible boom provides a custom fit for multiple users and close microphone positioning. The E6i is also available in an omnidirectional version for maximum control over wind noise and plosives (popping).

This E6i's sensitivity response is optimized to accurately capture strong vocals without noise and distortion. The high headroom is well suited for singers and performers in stage and broadcast applications.

Related Questions and Answers

Q: 1. What is the vertical tilt of the IB2? The Benro B2 lists vertical tilt of -45° to +90°. Thanks in advance.

A: The IB2 has a -45 (wall) to +90 (notch) angle as well.

Q: 2. Can you put two of these together, or is there another way to extend this further?

A: There is no provision to extend it further, the 6 foot extension only loses 1/10 of a stop.

Q: 3. Does the quick release plate locking knob incorporate a safety mechanism, such as pull and twist, similar to what is found on some other Benro ball heads?

A: Actually, there is a safety mechanism: once the pressure has been relieved on the ball by untwisting the knob, the knob must be pulled out and twisted once more to release the plate. Look at the pictures, where this mechanism can be seen.

Q: 4. Does it have a minimum balance weight?

A: Yes it does. This head has a load capacity between 8.8 to 26.4 pounds.

Q: 5. Not able to use this on the Manfrotto 536 tripod with the 75mm adapter attached. The bolt underneath the FSB 8 head doesn't seem to reach far enough past the bowl to be threaded into the clamp. What am I missing?

A: Hi, we just created a new longer shaft in order to make it posible to put the FSB 8 on a HotPod. I will test and let you know whether this solves your issue as well

Q: 6. What is the best way to secure the body of the AD600 Pro to the light stand after you attach this extension unit?

A: You may purchase a super clamp with a 5/8" stud such as the Impact Super Clamp with Ratchet Handle, B&H # IMCC106R • MFR # CC-106R, and the Impact 5/8" Snap-In Pin for Super Clamps (Black), B&H # IMSRP107 • MFR # SRP-107, which would then allow you to connect the Godox DP600PRP Extension Head for AD600Pro Flash Head to your light stand. https://bhpho.to/3iZLE5i https://bhpho.to/3wn1LwL

Q: 7. How long is the line length?

A: It is a six-foot cable (1.83m) and therefore correctly described in the other answer. This cable is three feet shorter than that of the extension head for the original AD600 so as to reduce the voltage drop. Because of that, the effect on the intensity of the light is a drop of only about 0.1 stops, which is absolutely minimal and excellent! Now, if you want to mount this extension head more than six feet above the ground, you can typically attach the AD600 Pro to the riser (i.e. vertical column) your C-stand or strong light stand with a super clamp and snap-in pin (A.K.A. spigot) so that it is within six feet of the extension head. Super clamp: https://bhpho.to/38nkJ8J Spigot: https://bhpho.to/2G1MkA8

Q: 8. Will this be compatible with 'MeFoto WalkAbout S Aluminimum' Monopod?

A: You would need a bushing adapter to make it work. You can use this one. https://www.bhphotovideo.com/c/product/769749-REG/Oben_OB_1039_3_8_16_to_1_4_20_Reducer.html

Q: 9. Will Manfrotto 190L tripod accommodate this head?

A: Yes it will.

Q: 10. Will this fit 501pl plate?

A: Fits arcs Swiss plates