The Countryman E6i Cardioid Microphone is a miniature ear-set microphone for virtually invisible operation in stage performances, trade shows, houses-of-worship, auctions, lectures and much more.

The cardioid version effectively minimizes off-axis feedback and noise from nearby monitor speakers, instruments and noisy sources. Flexible microphone positioning is maintained and the included windscreen minimizes the wind noise often associated with cardioid microphones.

The E6i is set apart from the original E6 with its softer flexible boom and silicon ear-pads. The flexible boom provides ease of boom adjustability to accommodate multi-user applications.

A wide variety of colors and connections are available for use with various wireless transmitters. This version is tan and features a Switchcraft TA4F connector for use with Revolabs wireless transmitters.

Switchcraft TA4F for Revolabs    2mm Diameter Duramax Cable    Headroom for General Speaking    Cardioid    Tan

A miniature cardioid capsule is mounted to a low-profile, flexible frame. This lightweight, unobtrusive design is available in various colors that virtually render the entire microphone invisible against the skin.

The included removable, quick-swap cable detaches from the actual headset, making it completely replaceable in the event of a short or break. The replaceable cable design makes upgrading wireless microphone systems easy, as they are available in a wide selection of connections to accommodate various wireless transmitters. The Duramax 2mm diameter cable provides extra strength, flexibility and durability.

The cardioid polar pattern is effective in minimizing off-axis residual noise from e nearby monitor speakers, instruments and loud sources. The result is increased signal-to-noise ratio and minimal feedback. The flexible boom provides a custom fit for multiple users and close microphone positioning. The E6i is also available in an omnidirectional version for maximum control over wind noise and plosives (popping).

This E6i's sensitivity response is optimized to accurately capture general speech without noise and distortion.

Related Questions and Answers

Q: 1. want to replace the mounting screw with aOBEN d RING- Oben 1/4 -20 Screw with D-Ring for RP Plates B&H # OBRPS14D MFR # RPS-14DWhen I contacted the agent, he said that it would not fit. This is the same plate used on Mefoto and I was told that MEfoto and Benro are the same. Is this true?

A: The Oben 1/4 -20 Screw with D-Ring for RP Plates B&H # OBRPS14D can work on Induro PU series plates which is the same plate as MeFOTO and Benro. Induro, MeFOTO and Benro are brands under the Mac Group.

Q: 2. can the quick plate of this ball head fit to a Peak Design capture clip?

A: No. Only Peak Design plates (either regular or dual plate) work with the Capture Clip. Inversely, the Peak Design plates would fit into this head.

Q: 3. Will this head work with the Sachtler Flowtech 75 tripod?

A: yes, it will

Q: 4. Does it comes with a half-ball in a box or not?

A: It does not.

Q: 5. What is the diameter of just the head cylinder, minus the knobs or plates?

A: it is 2.5 inches in diameter.

Q: 6. Are the old V1 batteries and this one interchangable? Can I use this battery in the old V1?

A: Unfortunately, the Godox VB30 Battery for V1Pro Flash Head is not compatible with the older V1. The batteries are not interchangeable.

Q: 7. So can a Really Right Stuff B2-LR-II Lever-Release Clamp (60mm) clamp be installed on this tilt head instead of the one that comes with it? What is the screw mount on the bottom of the tilt head 3/8-16?

A: You can install the Really Right Stuff B2-LR-II Lever-Release Clamp (60mm) on this head if you wish. The screw mount on the bottom of this head is 3/8-16 for mounting on most any monopod. This kit comes with a 3/8 to 1/4 bushing you need it.

Q: 8. Thinking of moving up from some manfrotto heads. Manfrotto uses two different rosette patterns for their panbars. Is the sachtler pattern the same as either of the manfrotto?

A: Manfrotto and Sachtler Tripods will have different rosette patterns for different pan bars. They will nto be cross compatible.

Q: 9. Which Plates are compatible besides the 504PLONG? Will they work with my other Manfrotto heads?

A: this is compatible with the Manfrotto 501PL Sliding Quick Release Plate with 1/4"-20 Screw

Q: 10. WHAT IS THE DIFFERENCE BETWEEN A 'DOUBLE' ACTION BALL HEAD, AND A 'TRIPLE' ACTION BALL HEAD?

A: This head should actually be listed as a triple action, but the triple action has an extra knob for controlling friction.