The tan Countryman E6 Omnidirectional Earset Mic, Low Gain with Detachable 1mm Cable and LEMO 6-Pin Connector for Micron Wireless Transmitters is a vocal microphone with an adjustable boom that weighs less than one tenth of an ounce and is designed to be used by only one person. Once adjusted, it will continually hold this shape.

The E6 earset can be used on either ear for capturing audio and rejecting unwanted sound, feedback, or surrounding noise from stage monitors or nearby speakers in houses of worship, theater, and outdoor vocal and speech applications.

The low-profile, omnidirectional E6 earset virtually disappears against the skin, so performers will forget they're wearing a mic. This version offers the lowest gain for the most powerful vocals that require the highest overload. In addition, the earset comes with three protective caps with different high-frequency response characteristics that control the amount of crispness or sibilance (response at 15 kHz). This omnidirectional E6 earset's cable terminates to a LEMO 6-pin connector for direct connection to Micron TX 700-Series wireless bodypack transmitters.

For Stage, Theater, and Broadcast TV    Fits Micron Transmitters    Headroom for Strong Vocals    Detachable 1mm Diameter Cable    Stiff, Steel Boom    Includes Windscreen    3 x Protective Caps    Black and White Single Tie Cable Clips    Carrying Case

The Countryman earsets are very small, lightweight, and the least visible headworn microphones.

The classic E6 is a good choice when one person will wear the microphone. Because the boom is stiffer, it can be adjusted to fit, then stored away and quickly reworn.

The E6's stainless steel boom is tough and can be bent and re-bent to fit different performers. It is highly resistant to makeup, sweat, and moisture when used with the supplied protective caps. The earset should always have a protective cap in place to keep sweat, makeup, and other foreign material out of the microphone.

The E6 earset's flexible boom is easily shaped right on the performer's face. Changeable protective caps let you shape the frequency response for different situations or to match other microphones. This omnidirectional version includes three protective caps—+4 dB (bright), +8 dB (very bright) and +0 dB (flat)—that controls the amount of crispness or sibilance (response at 15 kHz.)

Easy adjustment keeps the mic in a comfortable position for rejecting unwanted sounds. The omnidirectional E6 earset provides more isolation and is suitable for situations where there are loud monitors, extreme feedback, or environmental noise.

The included removable, quick-swap cable detaches from the actual earset, making it completely replaceable in the event of a short or break. The replaceable cable design makes upgrading wireless microphone systems easy as they are available in a wide selection of connections to accommodate most wireless transmitters.

Related Questions and Answers

Q: 1. Can the X1 trigger multiple flash units simultaneously, by, say, splitting the cable? I always do manual exposure control.

A: The Godox X1R-N TTL Wireless Flash Receiver for Nikon is only a receiver. If you have multiple units connect to non Godox flashes you can trigger all of them simultaneously. This unit is also use as a trigger for Nikon cameras. If you have a Godox flash connected to the camera hot shoe and other Godox flash units off camera, you can trigger all of them by connecting the camera with the remote cable that comes with the Godox X1R-N TTL Wireless Flash Receiver for Nikon. You will need to set your on camera flash as a transmitter.

Q: 2. Is this compatible with the d500

A: Yes.

Q: 3. Is this flash essentially the Yongnuo 568-EX with the YN622N transceiver built in?

A: No, it isn't. When off-camera, without a separate 622 TTL trigger, the YN685 does not give you TTL functionality. It will allow you to shoot in manual or multi mode, but the auto zoom feature will not work and TTL metering won't work. You can trigger the flash with a 603 or 622 transceiver, but will need a 622 for full TTL functionality.

Q: 4. Does the SU-800 work with the new D500?

A: Absolutely.

Q: 5. Does this trigger control power output while maintaining High speed syc with the Nikon SB910 speedlight while in manual mode? I may end up using A Godox strobe as my key light and speedlights as my fill lights.

A: I know this will work with Godox flashes I would do a test to see how it will work with the 910.

Q: 6. Someone said, If I print on Plain Paper, then colour of Laser printer will be better than IP8720! Is it true?

A: Laser printers and the IP8720 are very different machines. If you want to print high quality images go with IP8720. If photo quality is not an issue then go with a laser. Lasers are also significantly cheaper to operate. The PIXIMA does best when matched with photo quality paper.

Q: 7. I have the Godox X1T (O) on my Panasonic GH5. Will this item allow me to remote flash my Nikon SB800 flash when using my GH5?

A: The Godox X series system can fire a flash in manual so long as the camera transmitter match and the remote and flash match.

Q: 8. Will a pocket wizards work on top of this to fire other lights from another lighting system?

A: You could use a Pocketwizard on top of this, but in most cases it would be easier to just get a Godox receiver for the light.

Q: 9. If i connect the X1r-N to a non godox strobe via the 2.5 jack and fire it with a X1pro, will i be able to change the strobe power remotly? or it will just fire it.

A: No , it will just fire it.

Q: 10. Hi fellas, I have a Godox AD400Pro, the Xpro C transmitter & two Canon 600EXII-RT, and I'm trying to find out if this works. T

A: Yes, the Godox X1R-C TTL Wireless Flash Trigger Receiver for Canon flashes will work with your Godox ad400 and will become part of the echo system and react as one.