The cocoa Countryman E6 Omnidirectional Earset Mic, Standard Gain with Detachable 2mm Cable and 3.5mm Locking Connector for Sony Wireless Transmitters is a vocal microphone with an adjustable boom that weighs less than one tenth of an ounce and is designed to be used by only one person. Once adjusted, it will continually hold this shape.

The E6 earset can be used on either ear for capturing audio and rejecting unwanted sound, feedback, or surrounding noise from stage monitors or nearby speakers in houses of worship, theater, and outdoor vocal and speech applications.

The low-profile, omnidirectional E6 earset virtually disappears against the skin, so performers will forget they're wearing a mic. This version offers the highest gain for general speaking such as presentations or sermons. In addition, the earset comes with three protective caps with different high-frequency response characteristics that control the amount of crispness or sibilance (response at 15 kHz). This omnidirectional E6 earset's cable terminates to a 3.5mm locking connector for direct connection to Sony ZTX-B01 and ZTX-B02RC wireless bodypack transmitters.

For Stage, Theater, and Broadcast TV    Fits Sony Transmitters    Headroom for General Speaking    Detachable 2mm Diameter Cable    Stiff, Steel Boom    Includes Windscreen    3 x Protective Caps    Black and White Single Tie Cable Clips    Carrying Case

The Countryman earsets are very small, lightweight, and the least visible headworn microphones.

The classic E6 is a good choice when one person will wear the microphone. Because the boom is stiffer, it can be adjusted to fit, then stored away and quickly reworn.

The E6's stainless steel boom is tough and can be bent and re-bent to fit different performers. It is highly resistant to makeup, sweat, and moisture when used with the supplied protective caps. The earset should always have a protective cap in place to keep sweat, makeup, and other foreign material out of the microphone.

The E6 earset's flexible boom is easily shaped right on the performer's face. Changeable protective caps let you shape the frequency response for different situations or to match other microphones. This omnidirectional version includes three protective caps—+4 dB (bright), +8 dB (very bright) and +0 dB (flat)—that controls the amount of crispness or sibilance (response at 15 kHz.)

Easy adjustment keeps the mic in a comfortable position for rejecting unwanted sounds. The omnidirectional E6 earset provides more isolation and is suitable for situations where there are loud monitors, extreme feedback, or environmental noise.

The included removable, quick-swap cable detaches from the actual earset, making it completely replaceable in the event of a short or break. The replaceable cable design makes upgrading wireless microphone systems easy as they are available in a wide selection of connections to accommodate most wireless transmitters.

Related Questions and Answers

Q: 1. I have NikonD7100 and my speedlight is Godox V860II, does this trigger work well for my camera and if in future I wanna add Nikon flashes like Nikon sb700, Do you think it will be ok for the trigger?

A: buy the x1t-n that is the one you need this one is a receiver the other one is the transmitter it is a great trigger system and your flash have built in receiver and transmitter so it will work flawless. unless you want to trigger another flash with your v860II then this is the one you need.

Q: 2. Will this system work on SB 800 set on manual exposure? Or does it have to be set on TTL?

A: The SB-800 can be used in both TTL and manual when using this Godox trigger.

Q: 3. Can I use the X1N trigger as Commander to 2 SB-900s & an SB-500? Or would I have to trigger one of them to trigger the other 2? But then that would be a manual setting for each?

A: When I shot with Nikons, I had several SB900's. It is my understanding that they are optically triggered. The sensor is on the right side of the unit viewed from the back. The x1N is a RF unit. It does not have an optical output. If you wanted to operate the SB's, there is a receiver that can accomodate the SB's and that would allow the X1N to operate them. The real advantage to doing that would be the operating distance goes out to about 300 feet. So, putting the flash behind the subject would work well, when using the optical trigger would be difficult. Hope this helps.

Q: 4. can I use this for off-camera flash usages? I have a EF-42 flash and can't find a off-camera cable for it.

A: You will need to replace your EF-42 with a Godox flash, the TT350F or the TT685F are the models that will work with this transmitter and allow for TTL function.

Q: 5. does this work with canon sl3 camera

A: It can, if you do the firmware update V27.

Q: 6. Does this work with the GFX?

A: If you upgrade the firmware on the X1T-F to v03, it is compatible with the GFX 50s.

Q: 7. When using this trigger to manually control flash output, does it still do a pre-flash (the Odin's do this) prior to firing?

A: I never do pre-flashes, when I start shooting I turn on my flash I test the light than start shooting

Q: 8. Hvl f32m Sony flash is it compatible to this ?

A: With the addition of the Godox X1R-S TTL Wireless Flash Trigger Receiver for Sony B&H # GOX1RS on the HVL-F32M flash, you can use the X1T-S Transmitter to fire it.

Q: 9. I am migrating from a Nikon DSLR to Fuji X-T3, but would like to keep using my two SB-600 strobes (presently hooked up via a Yongnuo N system). Will two of the X1R-N, controlled from an XPro-F on the camera, do the job?

A: You can trigger your Nikon SB-600 flashes with X1R-N receivers on each from the Godox X-Pro F transmitter, but TTL is not guaranteed.

Q: 10. Will this trigger a Godox V860IIF ?

A: While off camera the Godox V860 will accept a signal from any of the Godox X1 or XPro transmitters. You Can TTL HSS and adjust power just like it was native. Its only when a Godox flash is on the camera shoe that the brand version matters.