The Countryman E6i Omnidirectional Microphone is a miniature earset microphone for virtually invisible operation in stage performances, trade shows, houses-of-worship, auctions, lectures and much more.

The omnidirectional version is most common in applications where feedback issues are not very likely. The microphone can be worn without a windscreen as the omnidirectional capsule provides excellent wind noise rejection.

The E6i is set apart from the original E6 with its softer flexible boom and silicon ear-pads. The flexible boom provides ease of boom adjustability to accommodate multi-user applications.

A wide variety of colors and connections are available for use with various wireless transmitters. This version is tan and features a Switchcraft A3M connector for Lectrosonics transmitters.

Switchcraft A3M for Lectrosonics    2mm Diameter Duramax Cable    Optimized for Strong Vocals    Omnidirectional    Tan

A miniature omnidirectional capsule is mounted to a low-profile, flexible frame with silicon ear pads. This lightweight, unobtrusive design is available in various colors that virtually render the entire microphone invisible against the skin. For more information on which color earset suits you best, refer to the Countryman support page.

The included 2mm Diameter Duramax Cable detaches from the actual headset, making it completely replaceable in the event of a short or break. The replaceable cable design makes upgrading wireless microphone systems easy, as they are available in a wide selection of connections to accommodate various wireless transmitters. The Duramax 2mm diameter cable provides extra strength, flexibility and durability.

The omnidirectional polar pattern is most effective in minimizing wind noise, plosives (popping) and handling noise. The flexible boom provides a custom fit for multiple users and close microphone positioning while minimizing off-axis noise. The E6i is also available in a cardioid version for maximum off-axis noise rejection in environments with high feedback and noise.

This E6i's sensitivity response is optimized to accurately capture strong vocals without noise and distortion. The high headroom is well suited for singers and performers in stage and broadcast applications.

Related Questions and Answers

Q: 1. is this Nitrotech different than the traditional fluid head?

A: It's a slightly different engineering concept (nitrogen pistons) than a traditional fluid head, but functions the same way. :)

Q: 2. Is the same plate used on this the same as the FSB 8 side load?

A: yes

Q: 3. Does the 128RC head weigh 1.7 lbs?

A: Yes it does.

Q: 4. While using the Sachtler FSB-8, what is the range of leveling from the Gitzo 75mm bowl adapter with the Gitzo series 5 tripod?

A: The Gitzo 75mm Bowl Adapter will allow you to connect 75mm ball tripods to the Gitzo Series 5 Tripods. While we have no specific information on the range of leveling it should work in the same way as it would if the head was connected to a tripod that already has a 75mm bowl.

Q: 5. Are there any travel restrictions or concerns with flying since it has a gas piston built in?

A: I can give two unofficial answers: (1) As an engineer who works with pressurized gases often, I'd bet a decent amount that the device is safe to travel in any aircraft. Consider: it has to maintain sealed pressure over years of use, and is surely built with a nice safety margin. So, a few hours at a very slightly higher delta-P is not going to make it fail. (2) Common sense suggests this tripod is unlikely to be noticed by anyone as a pressurized device; it's not exactly an aerosol can. But if you call attention to it, then our well-intended Barny Fife's of the world are almost certain to get excited. So, check it with confidence, and don't talk about it.

Q: 6. Is this head made in Italy or China ?

A: The Manfrotto MVH608 Nitrotech Head is made in Italy.

Q: 7. Is VB30 battery compatible with the Godox v860iii flash ? (asking because other related answers are not clear about that point)

A: The Godox VB30 Battery for V1Pro Flash Head will only work with the Godox V1Pro Flash at this time. It is not compatible with Godox VING V860II TTL Li-Ion Flash, The battery compatible with the v860II is the Godox VB-18 Li-Ion Battery Pack (11.1V, 2000mAh).

Q: 8. Can I attach an articulating arm (for a monitor) to the unused pan arm connector or does this go against the design?

A: On the articulating arms that B&H has available for mounting accessories, their end mounting screws are either 1/4'-20 or 3/8 -16. The screw holes Sachtler uses to mount their pan handles are an unlisted, unknown metric size so I am afraid the accessory articulation arms will not mount. Otherwise it is valid idea. So much so that Manfrotto makes some of their tripod heads to take 3/8 arms for just the purpose you are proposing. They call it Easy Link. Here is a comparable Manfrotto head with the Easy Link mounts, plus a Manfrotto arm. Manfrotto 509HD Professional Video Head B&H # MA509HD and Manfrotto 244 Micro Friction Arm B&H # MA244MICRO.

Q: 9. Is this compatible with the Godox AD600 Pro?

A: I think it is, because the flash tube socket looks difference from H600 but same with 600pro

Q: 10. The package weight is 0.9 lb. What is the weight of the item?

A: According to the manufacturer, the weight of the head is: 8.7 oz / 246 g.