The Matthews Doorway Dolly is designed with a wheel base of 28.25" without an extended axle. Overall length reaches 51" with a platform size of 27.5" x 41.5". The two side boards add 10" each. Ground clearance is 9" or 3" when inverted. Load capacity is 800 lb.

Constructed with a wooden platform attached to a steel tubing frame. The platform is fitted with a recessed camera tie-down and is carpeted for a non-slip, low maintenance surface.

Steering is accomplished with the use of a pull handle similar to a wagon, or it may be used in a secured upright position.

There is an angled fitting to allow the push bar to tilt down 340 for more clearance between the Dolly and the operator.

For extra low angles, the dolly can be inverted.

The rear wheels extend outward to provide greater operating stability.

All of the receivers have a Posi-V-Lock design when the pin is inserted, for a tight unitized fit.

Can be equipped with Matthews Hot Buttons for use on straight or curved track.

Related Questions and Answers

Q: 1. Can I use this with an OConnor 35L?

A: I don't know but probably.It looks like it will fit anything and its very nice.Kenny

Q: 2. Can this be used with a Series 3 Gitzo tripod with a pro DSLR and 600 mm lens?

A: It will easily support the weight and works with many tripods with rubber or spiked feet. This dolly's universal design allows compatibility with most tripod systems from a variety of manufacturers.

Q: 3. Does the eMotimo ST4 Dana Dolly Adapter Kit woks with this dolly?

A: Yes, the eMotimo Spectrum ST4 Pro Bundle + Dana Dolly Integration would work on this dolly.

Q: 4. Is it compatible with the Manfrotto 501PL QR?

A: I'm afraid not. This tripod's head has a specific quick release plate, the QR11.

Q: 5. Can it be used with Manor toot 502 tripod?

A: yes, i use it together

Q: 6. Can I use this Spreader Dolly with a Manfrotto MVH502A Tripod?

A: The Manfrotto MVH502A model number only details the fluid head, not the legs. This head can be used on and comes packaged with many different tripod legs. The legs are what are important when looking for a compatible tripod dolly. The Davis and Sanford W4DS tripod dolly is only compatible with tripods with spiked claw feet such as the Manfrotto 546B tripod legs (B&H # MAH502A546BK).

Q: 7. will this work with Manfrotto 028B Triman?

A: yes it will.

Q: 8. "In the box" doesn't say it includes rails, but the Q&A answer says that is does. Does it actually include rails, and what length?

A: Apologies, that answer has been corrected. The Glide Gear Dev Dolly Kit does not come with speedrail.

Q: 9. Will this work with the 645 and 635 Fast tripods? They have spiked feet

A: This Manfrotto 114MV Cine/Video Dolly for Tripods with Spiked Feet BH #MA114MV will work with the Manfrotto 635 and 645 Fast tripods.

Q: 10. Will this work with a Miller Solo 75 tripod?

A: The Benro DL-08 Tripod Dolly is not compatible with the Miller Solo 75 Tripod. The Benro DL-08 Tripod Dolly is compatible with the following tripods: Benro BV10 Tripod System Benro BV10H Tripod System Benro BV4 Tripod System Benro BV4Pro Tripod System Benro BV6H Tripod System Benro BV6Pro Tripod System Benro BV8 Tripod System Benro BV8H Tripod System Benro BV8Pro Tripod System Benro KH26 Benro S6Pro Tripod System Benro S7 Tripod System Benro S8 Tripod System Benro Single Leg Tripod Benro Tandem Leg Tripod GVM DX16 Magnus VT-4000-PRO Magnus VT-5000 Magnus VT-6000 Sirui BCT Series Tripod Legs Sirui SH25 Tripod System