This is a replacement Broncolor Halogen Modeling Lamp for the Boxlite softlight.

E14 Base

Related Questions and Answers

Q: 1. Should I get RFS 2.1 or 2.2 for X1D?

A: Either RFS2.1 or 2.2 NIkon is suitable and fully compatible with the X1D with the major difference being size, battery (coin-cell on 2.1, AA on 2.2) and control interface, the choice is yours.

Q: 2. What Broncolor trigger is needed for the Broncolor Grafit A4 / A2 power packs?

A: Yes the following RFS unit will communicate with the following Broncolor A4 / A2 units.

Q: 3. can this works on Hasselblad x1d

A: Yes, RFS2.2N works on the X1D with firmware v1.15.0 or later on the camera.

Q: 4. does this work on the Hasselblad x1d

A: Yes, RFS2.2N works on the X1D with firmware v1.15.0 or later on the camera.

Q: 5. 1. Is it possible to buy only the translucent plexiglass diffuser? Mine got an accidental bend.2. Is there an original metal adapter for Elinchrom heads? I'd like to use it also on my ELC 1000.

A: The outer diffusion can be ordered as part number B-32.459.00 (note that the item picture is incorrect at the time).

Q: 6. does the transmitter turn off?

A: According to page 7 of the PDF MANUAL it enters an energy saving mode at eight hours which may elicit a slight delay if a flash event occurs during this mode Flash triggering is synchronized either via the central contact of the hot shoeor the sync jack of the camera. Outdoors, the remote control range is up to50 m; indoors, it is up to 30 m. The transceiver is powered by a lithium buttoncell (Li-Mn CR2450). To minimise energy consumption, the transceiver is setto an energy-saving mode after eight hours have elapsed. If a flash triggeringaction occurs through the camera whilst the RFS 2 or RFS 2.1 transceiver isin energy-saving mode, a slight delay of the synchronization with the camerashutter release can take place. The RFS 2 or RFS 2.1 transceiver quits theenergy-saving mode after this flash release.attention: although this radio system allows the selection of up to 99 studioaddresses, the number of actually available channels depends on theconnected rFs 2 or rFs 2.1 flash unit. Battery life is listed as 8 - 12 months or 100,000 flasheshttp://www.bron.ch/uploads/tx_bronproducts/RFS2.1_30_09_2013_Englisch_01.pdf

Q: 7. Can I use my Profoto B1 at the same time using my Profoto Air Remote on top hot shoe?

A: The RFS2.2N features pass-through flash sync via its PC-Sync port or top hot shoe but does not transmit TTL information.

Q: 8. will this work on my sony camera as well in my phase one XF camera?

A: The RFS 2.2 S can be used with any camera with a sync output thanks to the transceiver's PC-Sync port on the side. The port can be configured as a sync input in this instance. The male shoe on the RFS 2.2 S however, is specific to the Sony style mount and will not fit other cameras. For use on standard (non-HS) camera hot shoes, we recommend the RFS 2.1 Transceiver.

Q: 9. Does this unit have 1 pin contact??? Does its also have PC sync attachment?

A: There is a single pin on the shoe and it accepts a miniphone to PC male cable on the side.

Q: 10. I have a pair of Canon 600EX-RT's and a ST-E3-RT. I know I won't be able to get the Broncolor's HSS to work with these. But, would I be able to a stick the ST-E3-RT on top of the RFS 2.2 and control the 600EX-RT's in standard shooting?

A: Hi Robert, Thanks for your question. The RFS2.2C's top hot shoe is only for x-sync only, meaning that while the flash would fire, any E-TTL or HSS signal would not be transmitted.