The 125' HD-SDI Video Coaxial Cable with BNC to BNC Connectors from Canare is a precision serial digital video coaxial cable that offers throughput for HD-SDI video signals for professional broadcast applications. Thanks to dual copper braids that impart high flexibility, the RG6 coaxial cable can be bent around tight corners or run through tight spaces while still providing high-quality, low-loss transfer.

18 AWG RG6 SDI Coaxial Cable    BNC Male to BNC Male Connectors    Solid Copper Center Conductor    Dual Copper Braids    Supports SMPTE 259M/292M/424M Standards    75-Ohm HD BNC Connectors    100% Sweep Tested

Transfers serial digital HD-SDI video signals for professional broadcast performance broadband facilities

18 AWG RG6 digital video coaxial cable

Dual copper braids for high flexibility and strength

Supports SMPTE 259M, 292M, and 424M standards

100% sweep tested

BCP-B series 75-ohm HD BNC connectors are capable of handling data rates that exceed 3 Gb/s SMPTE424M standards

Available in black, blue, green, and red colors

Related Questions and Answers

Q: 1. Can I feed HDMI in, and plug in SDI out on the other end?

A: Yes, you won't be able to use both at the same time with a single unit. But, you can feed in HDMI in on the transmitter and go SDI out on the receiver (vice versa).

Q: 2. Is it compatible with the Nikon D3300? It can output a clean, free from overlays feed on HDMI.

A: It should be, It has HDMI and mini BNC inputs, so far it takes signal form any device i have tried. I have not tried a Nikon camera, but it works with my Panasonic and JVC video cameras.

Q: 3. Blackmagic design video assist recorder support Video Signal Conversion HDMI to sdi ?

A: Yes, it will do HDMI to SDI or SDI to HDMI conversion.

Q: 4. I can't change zebra to over 85%-well I can, but it doesn't show anything! last stop is 85%, higher than this zebra just dissapears!Also i cannot change the date or the recording resolution and fps. Also even though my Video Assist is connected via SDI to my Ursa Mini, and trigger is set to 'over sdi' from the camera, pressing record on the camera doesn't start recording on Video Assist.Does anyone have any answers for this quite annoying errors?Nevertheless, it's a great piece of equipment!

A: I noticed a similar but somewhat different problem with my BMCC 2.5K, I have experienced the same Disappearing Zebra's as you have however in my case with my BMCC 2.5K I only loose them when I have my Zebra's set to ABOVE 90%, at 90% they are still there but if I go any higher they are gone. I have my monitor connected via SDI as well so after doing some research I think it might be and issue in part with SDI itself in terms of Legal vs Full range signal (Video vs Data (LOG) levels being transmitted over SDI I have noticed this problem before with RED EPIC and SONY Cine Alta Camera when connected to Blackmagic video devices like the Ultrascope 4K monitor, Both the REDs and Sony cameras are unable to show values above 95IRE on that Broadcast Ultracsope. I believe that because Blackmail Devices are geared toward Broadcast and Broadcast acceptable formats the Video Assist has trouble reading high values of luminance. It could also have to do with the SDI mode is your camera set to display Video dynamic range or Film domains range when you are in your camera's DISPLAY/MONITOR menu? When Blackmagic camera's are set to record RAW internally the SDI is automatically set to output 10-Bit LOG over SDI so the Video Assist might have trouble reading the LOG single over the SDI.In regards to SDI trigger problem, just set it to T/C Run instead of SDI, I know this sounds wrong because you have your camera connected over SDI but in my case with my BMCC 2.5K T/C Run works flawlessly.

Q: 5. Hello, what are the exact RF frequencies used for this item? I believe there are 12 different "channel" presets, but I would like to know the exact frequency in Hz because we have been struggling with some interference. Hopefully this information will help us to coordinate our RF environment. I need more detail than just "5Ghz".

A: Please contact Hollyland Mars directly: Email sales@hollyland-tech.com

Q: 6. Will this work with an android tablet like Amazon Fire/Samsung A- series? I don't want an iPad.

A: The Hollyland Mars 400S PRO Kit can use the Hollyview app, which is available for both iOS and Android OS.

Q: 7. Does this monitor have frame guides for different aspect ratios?

A: The Blackmagic Design Video Assist does not currently list having a frame line markers. Generally that is the job of the camera. However higher grade monitors like ones form Zacuto and Transvideo do have user controllable markers

Q: 8. Hello with this device I can connect to the receiver sdi and hdm signal simultaneously ?

A: Hi Manuel, yes of course.

Q: 9. Does this work with Red Helium 8K?

A: Yes, you will need one of the RED Expanders.

Q: 10. Can this act as a transmitter or will it just receive?

A: The Hollyland 400S Pro Receiver cannot act as a transmitter.