Patterns, or gobos, are widely used by designers in theatre, film, photography and television to create atmosphere, project scenery, and generally enhance the visual impact of their lighting.

Conceived by some of the world's leading lighting designers, the Rosco range presently includes hundreds of standard steel gobo designs.

To insure design integrity the patterns are etched using a precise double-sided process on stainless steel. The result is durable, high quality patterns which will withstand the extreme heat at the gate of ellipsoidal spotlights.

Rosco steel gobos are round to allow for rotation in the gate when aligning the projected image.

The standard "B" size is suitable for most fixtures with a 6" lens when used with a Rosco Pattern Holder or the holders of other manufacturers.

Trimming of patterns, where necessary, can be easily accomplished with a pair of scissors.

Related Questions and Answers

Q: 1. Does it work for iPhone 7 plus?

A: Yes, this would work with the iPhone 7 Plus.

Q: 2. How do you know the proper size?

A: At the bottom of each glove's page in its description, there are instructions and measurements for the size you need based on the circumference of your hand.

Q: 3. Are the gloves machine washable?

A: According to the manufacturer, these gloves can be hand-washed at a maximum temperature of 86 F(30 C). You can allow them to slowly dry and treat the leather with Heat Leather Balm, BH # HELB50ML. http://bhpho.to/2L56tLQ

Q: 4. Can the bluetooth be turned off completely using it as a wired keyboard?

A: Yes, the Plugable Full-Size Folding Bluetooth Keyboard with Case can be used as a wired keyboard via USB.

Q: 5. How can I securely mount this to a light stand or tripod with sand bags? What mounting adapters, threads, etc. would I need?

A: The correct adapters to mount this fixture to a stand or tripod will be as follows; Impact TVMP Yoke Mount to Baby Receiver or Junior Adapter, and Impact 5/8" Stud with 1/4"-20 Female Threads. The Impact 5/8" Stud with 1/4"-20 Female Threads will allow the conversion from tripod plate to the 5/8 baby receiver, this will connect to the Impact TVMP Yoke Mount to Baby Receiver or Junior Adapter.

Q: 6. What material is this tool made out of? Is it aluminum? The package weight is only 1 pound.

A: Falcon (Marshall) Personal-Size Paper Cutter is made out of an assorted composition of steel.

Q: 7. This is shown under accessories for a Mathews Medium High Roller stand, which has a 4 1/2" grip head, but the overview for the Kupo boom arm says it will fit "such as the Kupo 2 1/2" grip heads. Will it fit a 4 1/2" grip head?

A: Yes.

Q: 8. How far should the ridged top lift in order to remove the blade? Mine is only about 45' open and the blade isn't accessible. I'm afraid that the blade has shifted and is causing it to not be accessible. I would love to see a video of this process. I love this cutter, but need to replace the blade!

A: I would recommend contacting Falcon; Falcon (Marshall)Distributed By - Omega BrandessTel: (410) 374-3250 Website http://www.omegabrandess.com/ Email customerservice@omegabrandess.com

Q: 9. I love this cutter but how do you replace the razor blade?

A: 1-put finger under ribbed portion of sliding blade holder top and pull up. As it swivels (rotates) up it will expose blade2-Slide plastic holder of blade at top side of blade over,3- grab blade from top protected end and pull it strait up and out of holder.(it slides out sideways)4-slide new blade in exactly in reverse of how you pulled old blade out.5-slide plastic holder back over new blade top holding it in.6- Swivel (rotate)top of sliding blade holder back down into position and your ready to go.7- once you know how to do it the whole process takes ten seconds.

Q: 10. Will this trim a 13x19" sheet of photo paper to 12 x18"?

A: You will have trouble trimming 13" to 12". The Falcon Marshall can only cut up to 14". When you rotate the paper, you will only be able to trim one inch off that side, since you can only reach 14" on the long edge.