The green BodyBag Bridge from LensCoat is a rubber neoprene cover, which is ideal for storage and travel, that slips over select pocket-sized Canon and Nikon cameras. Moreover, point and shoot cameras with approximate dimensions of 4.9 x 3 x 4.6" will also fit the neoprene cover. Inside the cover there is a snap hook which attaches to the camera and stays tethered when the cover is taken off.

The rubber neoprene is shock-absorbing, which protects the camera against scratches and dents, and the front element disk protector provides additional protection to the camera's lens. Additionally, all the contents are kept secure, as well as dust and dirt-free, with the hook-and-loop closure.

Fits Select Point and Shoot Cameras    Shock-Absorbing Rubber Neoprene    Protects Against Scratches and Dents    Keeps Camera Dust and Dirt-Free    Hook-and-Loop Closure    Front Element Disk Protector    Ideal for Storage and Travel    Snap Hook Attaches to the Camera

Canon: PowerShot Pro1, Pro90 IS, SX10 IS, SX1 IS, SX30 IS, SX40 HS, SX50 HS, and SX60 HS
Nikon: COOLPIX 5700, 8700, 8800, P100, P90, P500, P510, and P530
Point and shoot cameras with approximate dimensions of 4.9 x 3 x 4.6"

Related Questions and Answers

Q: 1. Using the streaming bridge, can I feed lobby and sanctuary TV's with the SDI out plugs and use the HDMI output to feed a Boxcast device to Live Stream?

A: Yes, both the SDI and HDMI outputs have the same feed from the Bridge.

Q: 2. What is the intended usage(s) for the USB ATEM Utility (above the SDI outputs)? I don't see a USB output listed in the specs. Can the ethernet feed also exit the unit as USB (i.e. into a computer)?

A: The USB connection is for setup of the unit and firmware updates. There is no video function of the USB.

Q: 3. Can I take the ethernet out of the Atem Mini Pro into a network switch and send the video output to any or all of the network switch ports to output with ethernet to sdi/hdmi converters?

A: Yes, that should work. In the ATEM Control Software you will see the Stream Bridge come up as one of the options to stream to.

Q: 4. When streaming from an ATEM PRO to a Streaming Bridge, will the audio going with HDMI video (eg. a camera) also goes with?

A: On the ATEM the Blackmagic Design ATEM Streaming Bridge for ATEM Mini Pro Streaming Switchers two channels of embedded audio from the ATEM will stream to the Streaming Bridge and will be embedded into both SDI and HDMI outputs.

Q: 5. Does this device allow me to remotely control and switch cameras on the atem from a completely different location?

A: No, you cannot control or switch cameras on the ATEM from this device.

Q: 6. Related to a hardware functionality question on the Pro, will it be possible via firmware update to send a single fixed input to this device through Ethernet, and a switched program out through USB?

A: We can't predict if Blackmagic would be allowing that. For right now, this will just allow you to convert the IP signal into SDI and HDMI video.

Q: 7. Will this work with the Studio Pro HD?

A: No, that will not work.

Q: 8. What is the latency for internet streaming to the bridge?

A: The latency for internet streaming to the bridge Blackmagic Design ATEM Streaming Bridge for ATEM Mini Pro Streaming Switchers, can depend on the internet setup you are using. But an estimated to be around 1 second.

Q: 9. What are the SDI ref inputs used for exactly?

A: The Blackmagic Design ATEM Streaming Bridge for ATEM Mini Pro Streaming Switchers' Reference input is for syncing the video feeds via timecode or genlock.

Q: 10. Can it be used as program out from here ATEM Mini Pro ethernet and will it have latency via SDI and HDMI out?

A: The ATEM Mini Pro can stream via Ethernet to the ATEM Streaming Bridge. If the bridge is on a local network, the latency would be noticeable but under a second.