Inkpress Heavy Vinyl Paper 480 GSM, 36"x45' Roll is a water-resistant, opaque, light and flexible banner material with a very smooth surface. This product consists of a tear-resistant and flame retardant polyester fabric, which is embedded between two white vinyl layers.

Works with Pigment and Dye Based Inks    Water Resistant    Opaque    Light & Flexible    Indoor and Outdoor Usage    100% Polyester Fabric    Ideal for BannersPosters & Displays    Tear Resistance    15 Mil

Related Questions and Answers

Q: 1. Can the tripod legs support more than the 12 lbs stated? Is the supported weight limited by the head?

A: The Davis & Sanford TR654C-36 Traverse Carbon Fiber Grounder Tripod With Ball Head will not provide a solid support for more than 12 lbs--it may not fall down, but it won't be the steady support you need.

Q: 2. Can you insert the center column upside down with the camera below?

A: This tripod comes with a separate short center column for low profile shooting.

Q: 3. is this a study tripod? meaning, based on maximum extension of legs and column, will it shake or wiggle, or is it firm and steady?

A: This is a great carbon fiber tripod for the cost designed to support loads up to 12lbs.

Q: 4. What quick release plate will fit this ball head?

A: The ballhead comes with a Arca Quick release plate.See this ballhead for the Arca Quick release plate. Davis & Sanford PB-236-18 Powerball Dual Control Ballhead with Quick Release B&H # DAPB23618 MFR # PB236-18 NOTE: MFR # on ballhead is PB236-18A. The ballhead supplied with the product is MFR # PB236-18A (Similar to PB236-18).NOTE: The ballhead on the B&H photo on the product page is not the ballhead recieved with the tripod. The B&H photo shows a MFR # PB336-18. Davis & Sanford TR654C-36 Traverse Carbon Fiber Grounder Tripod With Ball Head B&H # DATCF4SGT MFR # TR654C-36 =======================================I am using an Acratech Quick Release Plate for Telephoto Lenses (3 ) B&H # ACQRLP3 MFR # 2181 that is attached to my Fujifilm XF 50-140mm f/2.8 R LM OIS WR Lens B&H # FU5014028 MFR # 16443060. Lens is attached to Fujifilm X-T1 Mirrorless Digital Camera (Body Only) B&H # FUXT1B MFR # 16421452.REASON: Did not like the arca quick release plate that came with the ballhead for this size lens attached support. This larger plate works fine with the ballhead. Balance of camera and lens is good. Plate locks down tight in the ballhead.========================================================I also have a Sunwayfoto PFL-XT1R L-Bracket for Fujifilm X-T1 B&H # SUPFLXT1R MFR # PFL-XT1R attached to my to Fujifilm X-T1 Mirrorless Digital Camera (Body Only) B&H # FUXT1B MFR # 16421452. I use the L Bracket vice the Arca Quick Release plate on the tripod when I am shooting with Fujifilm XF 16-55mm f/2.8 R LM WR Lens B&H # FU165528 MFR # 16443072 on my Fujifilm X-T1 camera. The L Bracket works great with the ball head. Easy to remove and locks down tight.=================================================NOTE: I have only been using the above setup recently. I going on a trip to Grand Teton, Yellowstone and Glacier National Parks in September 2015. I plan on writing a review after carrying on my backpack and using in the field. I do like the size and weight and how the tripod folds to compact size. I will have no problem putting the tripodin my luggage during flights. Also the load on the backpack is light. Curious how the tripod will perform in mountain winds.Mr. K.J. Smithamateur photographer

Q: 5. Can the ball head be removed and replaced with another tripod head if desired?

A: Yes, the tripod head comes off the TR654C-36 Traverse Carbon Fiber Grounder Tripod.

Q: 6. How well would this work with Nikon D750 and Sigma contemporary 150-600mm ?

A: I'm not familiar with your camera and lens but my experience with a Canon 5D Mark ii and a 24-105 Canon zoom was less than satisfactory. I found it a bit small for that task and had a hard time getting the quick release plate to stop turning on the camera especially shooting vertical orientation. Your lens sounds bigger than the 24-105 so I wouldn't recommend this tripod. Hope that helps!

Q: 7. Is this tripod the same as this one ''Sirui N-2204X Carbon Fiber Tripod''. It look as the same without the mono-pod leg?

A: No, this is not the same tripod.

Q: 8. How many bubble levels are on this tripod?

A: According to Davis & Sanford, the TR654C-36 Tripod with Ball Head has one bubble level.

Q: 9. What is weight and dimensions of this carton?

A: This information is provided on the B&H webpage for this item under SPECS on the green horozontal bar:Packaging InfoPackage Weight5.15 lbBox Dimensions (LxWxH)20.9 x 5.5 x 5.2

Q: 10. Is Maximum Height: 65" with or without centre-column extension? It is not clear from the description or the pictures.

A: The 65" (165.1 cm) maximum height of the Davis & Sanford TR654C-36 Traverse Carbon Fiber Grounder Tripod would be with the center column extended/raised.