RCF's 8" 300W Weatherproof 2-Way Speaker System is a weatherproof, full-range, wide-dispersion, coaxial two-way loudspeaker system offering substantial power and efficiency for a variety of professional indoor or outdoor applications.

The high-frequency section is a constant directivity CMD horn loaded with a 1" RCF precision compression driver with a 1.5" diaphragm assembly for smooth, wide dispersion. The low-frequency transducer is an 8" woofer with a 2.5" voice coil. The cabinet is a single piece rotational molded in medium density polyethylene and is fully UV protected.

The cabinet is equipped with 4 x M 8 brass inserts, a stainless steel U-Bracket. The front logo is in aluminum and rotatable.

The grille is in custom perforated aluminum with open-cell fibers and water-repellent woven fabric backing. The system meets the requirements of IP55 code.

Weatherproof cabinet IP 55

Aluminum grille

One 8" high-output LF transducer with 2.5" voice coil

One RCF precision 1" compression driver with 1.5" voice coil

60x90° constant directivity horn

Built in passive crossover

2x15° enclosure sides for array configurations

Active Mosfet Compression Driver Protection

4 brass suspension points (M8)

Input connector 4 pole Amphenol IP 67

Mounting hardware 304 stainless steel, highly resistant to corrosion and oxidation

Related Questions and Answers

Q: 1. Can I use this with Canon 750d for sigma 150-600 sports lens

A: The Manfrotto will work but with a large lens like the Sigma 150-600 Sport I think you would be happier with a head that has an Arca type plate so you will have at least two screws holding on the plate.I use the MT055PRO3 combination mainly for macro and lighter work and for lenses 5lbs. and up I use the Wimberley WH200 and Benro BENRO COM48CXL COMBINATION SER 4 CF tripod.The gimbal might be overkill but any quality head with an arca type will be better and more secure than the Manfrotto with the single screw.

Q: 2. Does this tripod work well with the Manfrotto 405 geared head for still life / product photography?Do I need any additional attachments to connect the head?

A: I've got an MHXPRO-3WG mounted on the MT055XPRO3 tripod and needed no extra parts/tools. The system is used for imaging 3D artwork in a light tent and works great. As noted in the other posts the 405 should also work well with the MT055XPRO3 tripod. Good luck with your quest...

Q: 3. Will this head fit on 3021 Manfrotto legs?

A: As long as the tripod has a flat top with a 1/4 screw this head will fit.

Q: 4. does this have a "leveler" showing a bubble in a liquid display, which if centered means the tripod is set up in a level position?

A: Yes it does. The Manfrotto XPRO Magnesium Ball Head included in this tripod kit has bubble levels on it.

Q: 5. Can you use this tethered with an added horizontal arm (e.g. manfrotto 131dd) attached to it holding a camera and laptop?

A: Yes, this will work with a lateral arm, but you may want to get a tripod with a higher load capacity. I would recommend the Benro TMA37, click the link below to view; https://bhpho.to/2CMGvIB

Q: 6. Will this fit on a gorillapod focus tripod?

A: This head has a fixed pan drag, so any time you panned you would probably end up twisting the head off when panning right to left; or simply twisting the legs of the Gorillapod and ruining your shot.

Q: 7. I would like to remove the center column. If I do there is no way to screw in a ball head. what part can I buy to attach to this tripod which would allow me to use the tripod with a ball head and no center column?

A: There is no short column option for this tripod. This Manfrotto tripod has the 90 degree lateral arm feature. Because of this mechanism, an alternative column cannot be used.

Q: 8. What is the diameter of the very bottom surface of the 808RC4?

A: Manfrotto 808RC4 3-Way, Pan-and-Tilt Head with 410PL Quick Release Plate base mount diameter is 60mm.

Q: 9. How does this head mount to a tripod?

A: This head mounts via a 3/8 -16 thread.

Q: 10. What country is this made in?

A: The Manfrotto MHXPRO 2-Way, Pan-and-Tilt Head with 200PL-14 Quick Release is made in Italy.