The Shinybow SB-6335T HDMI over Single CAT5e/6/7 Transmitter with Bi-Directional IR is an HDMI Version 1.4 transmitter that supports audio formats such as Dolby True HD, DTS-master, and all 7 types of 3D. This CAT5/5e/6/7 Transmitter is designed on technology which supports full 3D at 1080p up to a distance of 330’ (91.44 m). The SB-6335T not only supports high-definition video and audio, but also IR and RS-232. The front panel LED lights indicate a valid HDMI source, connection status, and power. The transmitter features built-in mounting tabs for surface mounting, and supports DVI with use of an external adapter (not included).

HDMI digital video/audio and video TMDS format support with HDCP compliance

Supports Dolby True HD, DTS-master.

3D-enabled

Accepts connections via the CAT5/5e/6/7 UTP/STP cable

Supports link speeds of up to 3.4 Gbps

Supports Digital RGB 36-bit HDMI TMDS format deep color

Extends high-quality 1920 x 1200 videos

Supports High Definition full range resolutions like 408p, 720p, 1080i/1080p

IR Extender support and RS-232 control

Surface-mountable

Can be installed easily without making any adjustments

DC power input with low power consumption (Full load 480 mA)

Power supply using universal power switch 12 VDC / 1250 mA

Related Questions and Answers

Q: 1. The D-lite 400RX4 is listed as fully compatible with the remote. What sync speed can I expect with a Canon 5D MKIII?

A: Elinchrom does not list a set of top sync speeds for individual cameras and/or strobe heads. They simply state that the Canon 5D Mark III and Elinchrom D-Lite RX4 would both be compatible with the Elinchrom EL-Skyport Transmitter Plus HS for Canon. While they state that you can get up to 1/8000 sec, a specific top maximum number is not given with each camera/flash combination. As such, I would have to recommend to simply test the setup with your equipment, then if needed or you experience banding at the shutter speed you wish to use, then I'd recommend to use their ODS (Over Drive Sync) Setup to fine-tune the Skyport HS's trigger to optimize exposure at high shutter speeds while gaining more light. The ODS value will vary depending on the camera and the flash unit which is used and must be adjusted manually.

Q: 2. When will they have one for Fuji camera's?

A: You can use the trigger already on Fuji. Its tested and triggers lights just fine. Only function you would be missing is HS. They mentioned in a Facebook post in March they will be supporting it next but since then I have seen no official word from them. So it is still, to be determined and no official release information from my understanding. Been waiting on this myself

Q: 3. Is this compatable with eos r with a rotolight ii?

A: This transmitter is compatible with the Canon EOS R as per the manufacturer to trigger both Elinchrom lamp heads with a Skyport receiver or the Rotolight NEO 2.

Q: 4. Can I adapt this to go on a tripod. The opening threads on bottom of head are much larger than receiving thread on tripod plate. Is there some kind of adapter?

A: The receiving end of this head is a 3/8"-16, which is the standard tripod mounting screw size. You would mount this directly to the tripod's legs rather than to a quick release plate or another head. Remove the tripod's current head first. There is an adapter you can use (called a bushing) but not for use as you described.

Q: 5. Can the bottom spike be removed to mount onto a manfrotto fluid base?

A: Hello Joshua: yes you can it has a screw..

Q: 6. Hello, Will this control and display the power for D-Lite 4 IT- which came with the Eco Skyport?

A: It with trigger and allow high speed sync but it will not change your power or display your power setting. That is according to the Elinchrom compatibility chart on their website.

Q: 7. What monopod head will support a sigma 150-600 mm lens?

A: The Manfrotto 234RC Tilt Head can support up to 5.5 pounds and the Sigma lens only weighs about 4 pounds. Your camera would probably add more than 1.5 pounds so you might technically exceed the maximum load capacity but this head should still be fine. If you are concerned about exceeding the load capacity, you could consider using a ball head such as this instead: https://bhpho.to/2Jjd7ta

Q: 8. Support Fujifilm GFX50S2?

A: Yes. The following unit is designed and made to work with the following TTL metering system.

Q: 9. Is this transmitter compatible with the GFX 100?

A: Yes

Q: 10. Is this head compatible with the Joby UltraFit Hand Strap with UltraPlate?

A: This item will not be compatible with the Joby UltraFit strap and UltraPlate, as Manfrotto uses a proprietary quick release system.