The Mini DisplayPort Male to VGA Female Adapter Cable from Comprehensive Cables allows you to connect your Mini DisplayPort source to a VGA display. The adapter supports resolutions up to 1920 x 1200 and lets you take advantage of your VGA capable display.

Supports PC Resolution up to 1920 x 1200    Supports HDTV Resolution up to 1080p

Supports Mini DisplayPort 1.1a input and VGA output

Mini DisplayPort 1.1a compliant receiver offering 5.4 Gbps bandwidth over two lanes

Integrated triple 10-bit, 162 MHz video DAC for analog VGA signal output

Supports up to 1080p, 1920 x 1200 reduced blanking video resolution

ID pass-through from PC source to display

Spread spectrum (de-spreading) for EMI reduction

Automatic sink detection

Power standby mode operation initiated based on sink detection status

Powered from Mini DisplayPort source

Related Questions and Answers

Q: 1. Hallo would you please tell me a little informtion about decklink mini monitor 4k card ,i cant find full information, is it only just for monitoring or its also works as acceleration card for effects

A: This is not an acceleration card, this is simply a video output card.

Q: 2. Does this work with apple silicon?

A: Yes, the Blackmagic Design DeckLink Mini Monitor 4K works with Apple silicon as well as intel based Macs.

Q: 3. Will this allow me to color grade HDR in Resolve through the HDMI to my HDR TV? Will I run into an important limitation that I should just upgrade to the next level?Windows 10TV - P65-C1

A: Yes. I use this exact card for HDR grading over the HDMI link. Note however, while my project is setup as 4K/59.94/10bit HDR, the output via this card is exactly half that (because it's limited to 4K/30), so I get 4K/29/97/10bit HDR to the grading monitor - this works perfectly well by skipping exactly every other frame on the grading monitor. The EOTF-2084 data gets through correctly, so the HDR luminance is correctly rendered to a HDR display. However, the thing to be aware of, the color space metadata is NOT sent by the card. Thus, to get the color correct you need to be able to set the color by the OSD on the monitor. I have used these cards with both Asus PA32UCX monitors, these work well and have a lot of color mode settings via the OSD to easily match to the color space you're using in Resolve and also the Asus PG27UQ, this can only be set to sRGB or "Wide Color" which is "Native Panel Gamut" this works as a good setting when you set the Resolve project to BT.2020. Note, with the PG27UQ you can't set the color space when in HDR mode, however, if you set the color space to "Wide" in SDR mode it carries over to HDR mode.

Q: 4. Can this VB212 power a Smallrig 220w video light?

A: Yes, with the appropriate power adapter plate and cable, the SmallRig x Caleb Pike VB212 Mini V-Mount Battery can power a SmallRig RC 220B Bi-Color LED Monolight (BH #SM3473) for approximately 30 minutes.

Q: 5. Is it possible to use this card to use a third monitor as a fullscreen preview monitor for Resolve in a Windows laptop? I'm considering buying this with an external enclosure (Akitio, Sonnet, etc) in order to have my 2 monitors for all the color grading windows and the third monitor as a fullscreen preview display... is it possible?

A: Yes, that setup will give you an SDI/HDMI fullscreen program output from Resolve.

Q: 6. Will this battery fit well on the Red Komodo X?

A: No, the SmallRig VB99 SE Mini V-Mount Battery (6800mAh) will not fit the RED DIGITAL CINEMA KOMODO-X 6K Digital Cinema Camera.

Q: 7. Is the 8V output voltage well suited for powering cameras that use a 7.4 VDC battery?

A: Yes, the 8V output of the SmallRig VB99 SE Mini V-Mount Battery would normally be the port that you would work with for cameras that support 7.4 battery types. SmallRig makes a number of dummy battery solutions that connect to the 8V output barrel connector, which regulates the voltage even further for the specific camera battery required. See the following link for some suggested DC coupler/dummy battery adapters: https://bhpho.to/3zbfsUu.

Q: 8. Does this output both SDI and HDMI at the same time if I want it to? Also, can I calibrate the attached monitor with a Spyder Elite as if it were a normal computer monitor?

A: The card always output to both SDI and HDMI in parallel. I don't think you can calibrate the monitor, but I didn't really try to.

Q: 9. How long will this battery last with an R5c?

A: The run time of the Canon EOS R5 C Mirrorless Cinema Camera on the SmallRig x Caleb Pike VB212 Mini V-Mount Battery will depend on your usage, settings, and the accessories attached. Generally one would expect around 5-7.5 hours of run time under normal conditions. Higher qualities, resolutions, frame rates, and additional accessories can reduce this run time.

Q: 10. I need to monitor 10 bit 4k on two displays (both support 10 bit 4k) from the same machine. Could I use 2 decklink cards on one system?

A: The software you are housing must support 2 cards. As well as the motherboard bus. If they are the same image use a distribution amplifier to feed the two monitors.