The Canare 75 ft HD-SDI Video Coaxial Cable - BNC to BNC Connectors (Green) is a precision serial digital video coaxial cable that offers throughput for HD-SDI video signals for professional broadcast applications. Thanks to dual copper braids that impart high flexibility and foam PE dielectric insulation, this RG6 coaxial cable can be bent around tight corners or run through tight spaces, while still providing a high-quality, low-loss transfer.

18 AWG RG6 SDI Coaxial Cable    BNC Male to BNC Male Connectors    Solid Copper Center Conductor    Dual Copper Braids    Supports SMPTE 259M/292M/424M Standards    75-Ohm HD BNC Connectors    100% Sweep Tested

Transfers serial HD-SDI video signals for professional broadcast broadband facilities

18 AWG RG6 digital video coaxial cable

Dual copper braids for high flexibility and strength

Supports SMPTE 259M, 292M, and 424M standards

100% sweep tested

BCP-B series 75-ohm HD BNC connectors are capable of handling data rates that exceed 3 Gbps SMPTE 424M standards

Suitable for use in HD-serial digital video transfer, mobile applications, HDTV upgrades, broadband facilities, etc.

Related Questions and Answers

Q: 1. Are any of the video codex's supported by Prem Pro CS5?

A: The Pro Res codec can be downloaded for use in CS5 from Apple.

Q: 2. While recording it seems to capture about 1 hour and 5 minutes at a time and starts a new clip. Is there a solution for this? I would just like to record everything instead of editing clips together.

A: This is a limitation with the QuickTime wrapper not ProRes. DNx MXF files wouldnt have a file break in the recording.The QuickTime files has a pre allocated header size where each frame's information is stored..as the QuickTime file is written out this header file is continually updated. When the header file is filled up a new QuickTime file is created.

Q: 3. My son does video work for school shows on 2 canon xh-a1s cameras. He wants to record onto memory cards instead of Mini DV tapes. Would this product achieve this?

A: The Canon XH-A1S has analog video outputs while the Video Assist has HDMI and SDI digital video inputs for capture. This will only work if you use an analog to HDMI or SDI converter in between.

Q: 4. Can this recorder display time/date and record it on the screen?

A: Details for the Video Assist are being worked out at this time and will not be known in full until release. Watch B&H for further information.

Q: 5. will this work with the Sony HDRfx7?

A: No. The Video assist does not record composite video

Q: 6. What are the correct HDMI cable to purchase to connect the BM Video Assist to the BM Design Micro Studio 4K?

A: Both the Video Assist and Micro Studio 4k have a 1.0/2.3 DIN connectors for their HD/SDI signal. Canare has a special cable that will allow these two products to work together. The Micro Studio 4k's HDMI output is for monitoring only, not recording, so you would need to use an HD/SDI cable for recording between these two devices.

Q: 7. I can't change zebra to over 85%-well I can, but it doesn't show anything! last stop is 85%, higher than this zebra just dissapears!Also i cannot change the date or the recording resolution and fps. Also even though my Video Assist is connected via SDI to my Ursa Mini, and trigger is set to 'over sdi' from the camera, pressing record on the camera doesn't start recording on Video Assist.Does anyone have any answers for this quite annoying errors?Nevertheless, it's a great piece of equipment!

A: I noticed a similar but somewhat different problem with my BMCC 2.5K, I have experienced the same Disappearing Zebra's as you have however in my case with my BMCC 2.5K I only loose them when I have my Zebra's set to ABOVE 90%, at 90% they are still there but if I go any higher they are gone. I have my monitor connected via SDI as well so after doing some research I think it might be and issue in part with SDI itself in terms of Legal vs Full range signal (Video vs Data (LOG) levels being transmitted over SDI I have noticed this problem before with RED EPIC and SONY Cine Alta Camera when connected to Blackmagic video devices like the Ultrascope 4K monitor, Both the REDs and Sony cameras are unable to show values above 95IRE on that Broadcast Ultracsope. I believe that because Blackmail Devices are geared toward Broadcast and Broadcast acceptable formats the Video Assist has trouble reading high values of luminance. It could also have to do with the SDI mode is your camera set to display Video dynamic range or Film domains range when you are in your camera's DISPLAY/MONITOR menu? When Blackmagic camera's are set to record RAW internally the SDI is automatically set to output 10-Bit LOG over SDI so the Video Assist might have trouble reading the LOG single over the SDI.In regards to SDI trigger problem, just set it to T/C Run instead of SDI, I know this sounds wrong because you have your camera connected over SDI but in my case with my BMCC 2.5K T/C Run works flawlessly.

Q: 8. what would be the 12V DC input amperage? i'm thinking about hooking up hi-capacity rechargeable battery to the DC instead if using canon style batt.

A: You can use any high capacity batteries and also can be use with D-Tap supported batteries.https://a href= http://www.bhphotovideo.com/c/product/1100258-REG/lanparte_dc_55_25_d_tap_to_dc_power.html target= _blank www.bhphotovideo.com/c/product/1100258-REG/lanparte_dc_55_25_d_tap_to_dc_power.html/a

Q: 9. Is the Kingston 64GB UHS-1 SDXC Memory Card (B&H # KISD64GBU3, MFR # SDA3/64GB) 100% compatible ?

A: The Kingston has matching specifications to the other cards we suggest for the Video Assist so you are good to go.

Q: 10. my system getting hot. is that normal or faulty system?

A: Yes, normal behavior for wireless video transmission system. They intend to get very warm.