Create a stable, secure truss setup for your equipment with this SQ-4126 3-Way 90° F34 Square Truss Corner from Global Truss, which is designed to work with F34 Square systems. This angle creates a 90° corner or turn in your system and has a length of 1.64', while the 3-way design allows it to sit as the top or bottom of a vertical setup. It also features a durable 6082-T6 aluminum alloy construction to match the rest of the system as well as similar measurements. This includes an outside diameter of 11.42", outside tubing measuring 1.97", 0.75" bracing, and a wall thickness of 0.08".

For F34 Square Truss Systems    90° Angle Corner    Length: 1.64'    Outside Diameter: 11.42"    Outside Tubing Diameter: 1.97"    Bracing: 0.75"    Wall Thickness: 0.08"    6082-T6 Aluminum Alloy Construction

Related Questions and Answers

Q: 1. What is the base diameter on the Manfrotto MHXPRO ?

A: The base diameter of the Manfrotto MHXPRO 2-Way, Pan-and-Tilt Head is 2.25 inches which translates to about 57mm

Q: 2. Will this fit on a gorillapod focus tripod?

A: This head has a fixed pan drag, so any time you panned you would probably end up twisting the head off when panning right to left; or simply twisting the legs of the Gorillapod and ruining your shot.

Q: 3. Does this tripod works with the 322RC2 head?

A: Yes this would work with the 332RC2 head perfectly fine since it is a standard 3/8" thread.

Q: 4. Is this considered a flat base head that would work with a slider?

A: Yes. This video head is a good choice for sliders.

Q: 5. Hi, which Pan Bar Handles are compatible with this head?

A: Manfrotto does not offer any pan handle options other than the handle that is included with the Manfrotto MHXPRO 2-Way, Pan-and-Tilt Head.

Q: 6. Need to balance large telephoto (Tamron 150-600mm) on D7500, is there a way to put on a arca swiss plate or other sliding system for balancing?

A: Yes, but only with an adapter. I have "Haoge Quick Release QR Clamp Adapter Convertor for Manfrotto RC2 System to Arca-Swiss Compatible" permanently attached for exactly that purpose. It attaches to the Manfrotto 200PL socket on this head and then accepts standard Arca-Swiss plates.

Q: 7. Could I remove the center column and replace it with a Manfrotto Leveling Center Column with 50mm Leveling Ball?

A: The center column on the Manfrotto MT055XPRO3 Aluminum Tripod can be removed and replaced with the Manfrotto 555B Leveling Center Column - for 055 Pro and 3021 Pro Tripods, BH #MA555B.

Q: 8. Is the plate ARCA type?

A: No, but it is adaptable to arca-swiss. I use a "Haoge Quick Release QR Clamp Adapter Convertor for Manfrotto RC2 System to Arca-Swiss Compatible" ... you'll have to search for it. I have it permanently installed on this head for use with my standard Arca Swiss plates.

Q: 9. Does anyone know why they shortened the height on this newer model from the old Manfrotto Pro 055XPROB? The new one only extends to 66.9 whereas the old version goes up to 70.3 , side by side the new one is actually taller at the base but the center column is much taller on the older version, which is why the the height is taller so did they shortened this column for stability reasons?

A: I never raise the center column. On several of my tripods I cut the center post so I can get closer to the ground for micro work with plants. However this has been the best Manfrotto tripod I've used.

Q: 10. Is B&H an authorized Manfrotto dealer?

A: Yes, they absolutely are.